Hitachi P1-00080-L Basic Manual page 89

Chapter 4
[Output terminal function list]
Function
Symbol Function name
code
040 ZS 0Hz detection signal
Maximum Speed
041 DSE
deviation
Maximum position
042 PDD
deviation
Positioning
043 POK
completed
Pulse counter
044 PCMP
compare output
Output deviation
045 OD
for PID control
PID feedback
046 FBV
comparison
Output deviation
047 OD2
for PID2 control
PID2 feedback
048 FBV2
comparison
Communication
049 NDc
disconnection
Analogue Ai1
050 Ai1Dc
disconnection
Analogue Ai2
051 Ai2Dc
disconnection
Analogue Ai3
052 Ai3Dc
disconnection
Analogue Ai4
053 Ai4Dc
disconnection
Analogue Ai5
054 Ai5Dc
disconnection
Analogue Ai6
055 Ai6Dc
disconnection
Window
056 WCAi1
comparator Ai1
Window
057 WCAi2
comparator Ai2
Window
058 WCAi3
comparator Ai3
Window
059 WCAi4
comparator Ai4
Window
060 WCAi5
comparator Ai5
Window
061 WCAi6
comparator Ai6
Logical operation
062 LOG1
result 1
Logical operation
063 LOG2
result 2
Logical operation
064 LOG3
result 3
Logical operation
065 LOG4
result 4
Logical operation
066 LOG5
result 5
Logical operation
067 LOG6
result 6
Logical operation
068 LOG7
result 7
Description
ON if output frequency is
less than set value
ON if speed deviation
exceeds the set value
ON if position deviation
exceeds the set value
ON if positioning is
completed
ON when set value and
pulse train comparator
matches.
ON if PID control deviation
exceeds the set value
ON if PID feedback is
within range
ON if PID control deviation
exceeds the set value
ON if PID feedback is
within range
ON if communication is
lost with operation keypad
ON if Analogue input 1 is
less than the set value
ON if Analogue input 2 is
less than the set value
ON if Analogue input 3 is
less than the set value
ON if Analogue input 4 is
less than the set value
ON if Analogue input 5 is
less than the set value
ON if Analogue input 6 is
less than the set value
ON if Analogue input 1 is
within range
ON if Analogue input 2 is
within range
ON if Analogue input 3 is
within range
ON if Analogue input 4 is
within range
ON if Analogue input 5 is
within range
ON if Analogue input 6 is
within range
Determined by the
calculation results of two
output terminals
4-41
For parameter configuration
[Output terminal function list]
Function
Symbol Function name
code
069 MO1 General-output 1
070 MO2 General-output 2
071 MO3 General-output 3
072 MO4 General-output 4
073 MO5 General-output 5
074 MO6 General-output 6
075 MO7 General-output 7
Emergency force
076 EMFC
drive indicator
Bypass mode
077 EMBP
indicator
078 WFT Trace waiting signal
079 TRA Trace running signal
Low battery of
080 LBK
operation keypad
Power source over
081 OVS
voltage
084 AC0 Alarm code bit 0
085 AC1 Alarm code bit 1
086 AC2 Alarm code bit 2
087 AC3 Alarm code bit 3
Over deviation for
089 OD3
PID3
PID3 feedback
090 FBV3
comparison
Over deviation for
091 OD4
PID4
PID4 feedback
092 FBV4
comparison
093 SSE PID soft start error
Description
Set if case of use of EzSQ
ON while in force
operation
ON while in bypass
operation
ON while in waiting status
ON while in stand-by
ON while in low battery or
when no contain battery
on keypad
ON when become
overvoltage in stop status
ON if detects low battery
Alarm information is
delivered as bit.
Use the user's guide for
more information.
ON when PID deviation
exceeds the value [AJ-37]
ON when PID feedback is
between [AJ-38]/[AJ-39]
ON when PID deviation
exceeds the value [AJ-57]
ON when PID feedback is
between [AJ-58]/[AJ-59]
ON when PID soft start
became in warning status