GE C60 Instruction Manual page 345

CHAPTER 5: SETTINGS
Operand type Operand syntax
INPUTS/OUTPUTS: Cont Op 1 VOn
Contact outputs, Cont Op 2
voltage ↓
(from detector on Cont Op 64
form-A output only)
Cont Op 1
Cont Op 2
↓
Cont Op 64
INPUTS/OUTPUTS: DIRECT INPUT 1 On
Direct inputs ↓
DIRECT INPUT 32 On
INPUTS/OUTPUTS: RxG DPS 1 BAD
RxGOOSE DPS RxG DPS 1 INTERM
RxG DPS 1 OFF
RxG DPS 1 ON
RxG DPS 2 to 5
INPUTS/OUTPUTS: RxG Bool 1 On
RxGOOSE Booleans RxG Bool 2 On
RxG Bool 3 On
↓
RxG Bool 256 On
INPUTS/OUTPUTS: Virt Ip 1 On
Virtual inputs Virt Ip 2 On
Virt Ip 3 On
↓
Virt Ip 64 On
INPUTS/OUTPUTS: Virt Op 1
Virtual outputs Virt Op 2
Virt Op 3
↓
Virt Op 96
LED INDICATORS: LED IN SERVICE
Fixed front panel LED TROUBLE
LEDs LED TEST MODE
LED TRIP
LED ALARM
LED PICKUP
LED VOLTAGE
LED CURRENT
LED FREQUENCY
LED OTHER
LED PHASE A
LED PHASE B
LED PHASE C
LED NEUTRAL/GROUND
LED INDICATORS: LED TEST IN PROGRESS
LED test
LED INDICATORS: LED USER 1
User-programmable
LEDs
LED USER 2 to 48
PASSWORD ACCESS LOC SETG OFF
SECURITY ACCESS LOC SETG ON
ACCESS LOC CMND OFF
ACCESS LOC CMND ON
ACCESS REM SETG OFF
ACCESS REM SETG ON
ACCESS REM CMND OFF
ACCESS REM CMND ON
UNAUTHORIZED ACCESS
C60 BREAKER PROTECTION SYSTEM – INSTRUCTION MANUAL
Operand description
(does not appear unless ordered)
VOn (does not appear unless ordered)
↓
VOn (does not appear unless ordered)
VOff (does not appear unless ordered)
VOff (does not appear unless ordered)
↓
VOff (does not appear unless ordered)
Flag is set, logic=1
↓
Flag is set, logic=1
Asserted while the RxGOOSE double-point status input is in the bad state
Asserted while the RxGOOSE double-point status input is in the intermediate
state
Asserted while the RxGOOSE double-point status input is off
Asserted while the RxGOOSE double-point status input is on
Same set of operands as per RxG DPS 1
Flag is set, logic=1
Flag is set, logic=1
Flag is set, logic=1
↓
Flag is set, logic=1
Flag is set, logic=1
Flag is set, logic=1
Flag is set, logic=1
↓
Flag is set, logic=1
On Flag is set, logic=1
On Flag is set, logic=1
On Flag is set, logic=1
↓
On Flag is set, logic=1
Asserted when the front panel IN SERVICE LED is on
Asserted when the front panel TROUBLE LED is on
Asserted when the front panel TEST MODE LED is on
Asserted when the front panel TRIP LED is on
Asserted when the front panel ALARM LED is on
Asserted when the front panel PICKUP LED is on
Asserted when the front panel VOLTAGE LED is on
Asserted when the front panel CURRENT LED is on
Asserted when the front panel FREQUENCY LED is on
Asserted when the front panel OTHER LED is on
Asserted when the front panel PHASE A LED is on
Asserted when the front panel PHASE B LED is on
Asserted when the front panel PHASE C LED is on
Asserted when the front panel NEUTRAL/GROUND LED is on
An LED test has been initiated and has not finished
Asserted when user-programmable LED 1 is on
The operand above is available for user-programmable LEDs 2 through 48
Asserted when local setting access is disabled
Asserted when local setting access is enabled
Asserted when local command access is disabled
Asserted when local command access is enabled
Asserted when remote setting access is disabled
Asserted when remote setting access is enabled
Asserted when remote command access is disabled
Asserted when remote command access is enabled
Asserted when a password entry fails while accessing a password protected
level of the C60
FLEXLOGIC
5
5-177