Related Manuals for Hubsan H502S
Summary of Contents for Hubsan H502S
- Page 1 ® Ages 14+ READ THE INSTRUCTION MANUAL CAREFULLY PLEASE VISIT WWW.HUBSAN.COM FOR UPGRADE. THE HUBSAN FPV X4 DESIRE ITEM NO: H502S FOLLW ME FUNCTION AND RTH FUNCTION SEE PAGE 17-19 ARM/DISARM MOTORS SEE COMPASS CALIBRATION SEE TRANSMITTER CALIBRATION SEE...
- Page 2 Hubsan FPV X4 Desire 2015.01 V1.0 Please read the instruction manual carefully! IMPORTANT SAFETY NOTES OPERATION: Be extremely careful and responsible when using the drone. Small electronic components can be damaged by crashing or by dropping the X4 into water. To avoid further damages, please replace the broken spare parts in time.
- Page 3 INTRODUCTION Thank you for buying the HUBSAN product. It is designed as an easy-to-use, multi-functional RC model, capable of hovering, fast forward and aerobatic flight maneuvers. Please read the manual carefully and follow all the instructions. Be sure to keep the manual for future reference.
- Page 4 3.1 INTRODUCTION The quad copter battery is a rechargeable lipo battery with 610mAh capacity and 7.4V voltage. The battery should only be charged with the HUBSAN charger. Please make sure the battery being fully charged before the first time use.
- Page 5 Please match the “I” mark on propellers to the “D” gap on motor shafts when assembling as figure 1 shows. ● Make sure that the A and B propellers installed correctly. The X4 will not fly if propellers were improperly installed. © 2015 Hubsan 哈博森科技 版权所有...
- Page 6 Do not stop the motors during the flight to avoid any crash. Push the sticks as slightly as you can. Release the sticks after the motors armed or disarmed. © 2015 Hubsan 哈博森科技 版权所有...
- Page 7 Push the stick to the right and the X4 will fly to right. The X4 will keep the current status when the Left Right stick in center. The flight speed and tilt angle have connection with the angle when push the sticks. © 2015 Hubsan 哈博森科技 版权所有...
- Page 8 2. When the memory of SD card is full, he screen will display “SD Full”. 3. It is best to use a class 4+ SD card, and the capacity should no less than 4GB. 4. Format the SD card in the transmitter before use. © 2015 Hubsan 哈博森科技 版权所有...
- Page 9 The flight control system will control the quad copter fly back to the home point and landing automatically. The RTH MODE only works when the GPS mode is activated with no less than 6 satellites. The Home Point is recorded when armed the motors with no less than 6 GPS satellites. © 2015 Hubsan 哈博森科技 版权所有...
- Page 10 Press the stick again to exit headless Mode, indicated by one "beep" sound and the ”Headless Off” displays on the LCD. 6.4 FOLLOW ME MODE Follow me mode means the drone follows the transmitter automatically due to the built-in GPS system. MODE 2 MODE 1 © 2015 Hubsan 哈博森科技 版权所有...
- Page 11 If the quantity of GPS satellites drops below six for more than 20 seconds while the X4 is returning to home, the X4 will descend automatically. The X4 will not avoid obstacles automatically while in failsafe mode. You must set the height value to avoid obstacles in the flight path. © 2015 Hubsan 哈博森科技 版权所有...
- Page 12 No function 12 GPS SW 13 RTH SW HOME 8 Photo 8 Video 6 Throttle Trim 4 Elevator Trim 1 Throttle /Rudder Stick 2 Elevator/Aileron Stick 7 Power SW 5 Rudder Trim 3 Aileron Trim (MODE 2) © 2015 Hubsan 哈博森科技 版权所有...
- Page 13 Press video button and start the record and press again to stop Video glasses socket Connect Hubsan video glasses (The video glass is excluded) The TF card can be inserted into the card plug on theTX or the TF card plug quad copter.
- Page 14 Pull the throttle stick to the lowest position and long press the Elevator stick to enter into the MAIN MENU interface. Push the Elevator stick up/down to select “Set Sensitive”, push the stick right to enter into the “ set sensitive” interface, select “Expert mode” or “ Normal mode”. Select” Exit” to exit. © 2015 Hubsan 哈博森科技 版权所有...
- Page 15 2. If the batteries in the transmitter runs low while flying the X4, you can still control the X4, please land the X4 and then replace batteries. 3. The Transmitter can only use 2S Lipo batteries, 4XAA batteries or NI-MH AA batteries, other batteries will damage the Transmitter. 2015 Hubsan 哈博森科技 版权所有...
- Page 16 Hold down the throttle stick screen displays “Calib compass 1” Rotate the X4 in clock-wise Put the X4 nose down and rotate until the LCD screen displays it in counter clock-wise until “Calib compass 2” the ‘Calib compass 2” disappears © 2015 Hubsan 哈博森科技 版权所有...
- Page 17 MAIN MENU interface. Push the Elevator stick up/down to select “5.8G Frequency”, push the stick to the right to enter into the “ 5.8G frequency” interface, select a matched frequency. 0:08:49 0:08:49 MAIN MENU 5.8G FREQUENCY Set Reverse Exit Set Sensitivity 5730MHZ 5.8G Frequency Set Manual Exit © 2015 Hubsan 哈博森科技 版权所有...
-
Page 18: Exploded View
EXPLODED VIEW © 2015 Hubsan 哈博森科技 版权所有... - Page 19 Motor Holder Camera Module Rotary Gear Motor Gear Motor A Motor B Motor Shaft Li-Po Battery Bearing Screw 5.8G Attenna 2.4G Attenna Screw Upper Boby Shell Screw GPS Shielding Case Screw Battery Cover Screw Lens Holder © 2015 Hubsan 哈博森科技 版权所有...
- Page 20 H502S SPARE PART CHART H502-04 H502S-01 H502-01 H502-02 H502S-02 H502-03 Screw Set Body Shell Set Battery Cover Eye Lampshade Lens Holder Lamp Base A/B H502S-03 H502-05 H502-06 H502-07 H502-08 H502-09 Propeller A/B Motor A Motor B Motor Holder Bearing Motor Gear A...
-
Page 21: Fcc Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. © 2015 Hubsan 哈博森科技 版权所有... - Page 22 User manual is subject to change without prior notice due to unforseen product upgrades. Download the latest user manual from WWW.HUBSAN.COM VERSION 1.0 EN...