Table of Contents
Advertisement
Chapter 2 - Hardware Installation
Board Layout
DC-in
24
Clear CMOS
Data (JP8)
4-pin Power
(optional)
1
12
Standby
Power LED
USB 1
USB 3.0
USB 1-2 Power
1
Select (JP5)
USB 2
USB 2.0
Intel Atom
VGA
E3800 Series
ISL95837
SMSC
USB4604
COM 1
ASMedia
Intel
2
ASM1182
1
WGI210AT
USB 2.0
2
USB 4-5
1
1
CPU Fan
Intel
LAN 1
WGI210AT
USB 4-5 Power Select
Mini PCIe/mSATA Signal Select
SATA 1/mSATA Signal Select
LAN 2
Mini PCIe
Mini PCIe/mSATA
1
Power Select (JP6)
COM 4
RS232/422/485
Select
COM 4
RS232/Power
DFI Proprietary
Select
Extension Bus
Chapter 2 Hardware Installation
Digital I/O
13
1
1
Digital I/O
System
1
1 1
1
Power
Auto Power-on
Fan
ATX Power
1
(JP18)
12
11
Select (JP12)
(JP20)
(JP17)
Front
Panel
Digital I/O Power Select
(JP17)
Digital I/O 0-3 Output State
(JP20)
2
1
Digital I/O 4-7 Output State
(JP18)
Buzzer
Dimming Mode Select
(JP15)
Backlight Power Select
(JP16)
Note:
SATA0 supports SATA DOM.
SATA
LCD/Inverter
8 7
Battery
LPC
USB 2.0
SATA 2.0
Power 0
Power
LAN2 State
12
LAN2 State
USB 3
SATA 0
11
1 2
1
LAN1 State
4
(JP7)
1
LAN1 State
10
3
12
3
12
1
(JP15)
1
2 1
(JP16)
1
1
1
6
5
LCD/Inverter Power
1
Panel
9
1
10
1
10
Select (JP21)
(JP9)
(JP10)
4
Power
Select
Chassis
39
40
1
(JP19)
Intrusion
2
1
(JP7)
COM 2
SATA DOM Power
2
10
1
1
Select (JP13)
(JP9)
1
USB 3 Power
(JP10)
LVDS LCD
Select (JP14)
1
9
1
Panel
2
COM 3
10
1
SPI
Flash
BIOS
1
9
4
NXP
2
10
PTN3460
SATA
Power 1
1
2
COM 4
SATA 1
SATA 2.0
1
9
(JP22)
2
6
2
6
2
6
2
6
(JP23)
(JP25)
1
5
1
5
1
5
1
5
(JP24)
(JP24)
(JP22) (JP25) (JP23)
Chapter 2
Important:
Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in
boards, and other components. Perform installation procedures at an ESD workstation
only. If such a station is not available, you can provide some ESD protection by wear-
ing an antistatic wrist strap and attaching it to a metal part of the system chassis. If
a wrist strap is unavailable, establish and maintain contact with the system chassis
throughout any procedures requiring ESD protection.
System Memory
Important:
When the Standby Power LED lights red, it indicates that there is power on the sys-
tem board. Power-off the PC then unplug the power cord prior to installing any de-
vices. Failure to do so will cause severe damage to the motherboard and components.
Rear I/O
Onboard I/O
Storage
Expansion
Important:
Although ECC and non-ECC SODIMMs share the same socket together, ECC SODIMMs
cannot be pinout compatible with standard, non-ECC SODIMMs.
9
Standby
Power LED
DDR3L-1
DDR3L-2
www.dfi .com
Advertisement
Table of Contents
