Copyright FCC and DOC Statement on Class B This publication contains information that is protected by copyright. No part of it may be re- This equipment has been tested and found to comply with the limits for a Class B digital produced in any form or by any means or used to make any transformation/adaptation without device, pursuant to Part 15 of the FCC rules.
About this Manual Static Electricity Precautions An electronic file of this manual is included in the CD. To view the user’s manual in the CD, in- It is quite easy to inadvertently damage your PC, system board, components or devices even sert the CD into a CD-ROM drive.
About the Package The package contains the following items. If any of these items are missing or damaged, please contact your dealer or sales representative for assistance. • One BT700 board • One DVD • One QR (Quick Reference) •...
Chapter 1 Features Specification Comparison Table The table below shows the Qseven standard specifications and the corresponding specifications supported on the BT700 module. • DDR3L ARM/RISC Based X86 Based Minimum Maximum DFI BT700 System I/O Interface DDR3L is a higher performance DDR3 SDRAM interface providing less voltage and higher...
Chapter 2 Chapter 2 - Hardware Installation Block Diagram Board Layout LVDS PTN3460 2GB/4GB DDR3L P9145 memory down DDR3 1333MHz Single Channel SM Bus SM Bus SM Bus SM Bus Intel Atom PTN3460 DDR3L Top View PCIe x1 3x PCIe x1 3x PCIe x1 3x Switch E3800 Series...
“1” and “2“ denote the locations of the thermal pads designed to contact the corresponding components that are on BT700. • Remove the plastic covering from the thermal pads prior to mounting the heat sink onto BT700. Chapter 2 Hardware Installation www.dfi .com...
Chapter 2 MXM Connector MXM Connector The MXM connector is used to interface with the carrier board. Insert BT700 to the MXM con- nector on the carrier board. Refer to the following pages for the pin functions of this connec- tor.
Page 12
Chapter 2 Pin Q7 R2.0 Signal BT700 Signal Pin Q7 R2.0 Signal BT700 Signal Pin Q7 R2.0 Signal BT700 Signal Pin Q7 R2.0 Signal BT700 Signal 1 GND 2 GND 117 GND 118 GND 3 GBE_MDI3- GBE_MDI3- 4 GBE_MDI2- GBE_MDI2-...
Push Pull NC Not Connected PCI Express Interface Signals Descriptions Signal Pin# Pin Type Pwr Rail /Tolerance BT700 Carrier Board Description PCIE0_RX+ Device - Connect AC Coupling cap 0.1uF I PCIE PCIE PCI Express channel 0, Receive Input differential pair.
Page 14
Chapter 2 Serial ATA Interface Signals Signal Pin# Pin Type Pwr Rail /Tolerance BT700 Carrier Board Description SATA0_RX+ AC Coupling capacitor I SATA SATA Connect to SATA0 Conn RX pin Serial ATA channel 0, Receive Input differential pair. SATA0_RX- AC Coupling capacitor...
Page 15
Chapter 2 LVDS Flat Panel Signals Signal Pin# Pin Type Pwr Rail /Tolerance BT700 Carrier Board Description Connect to enable control of LVDS panel power circuit LVDS_PPEN O CMOS 3.3V/3.3V Controls panel power enable. Connect to enable control of LVDS panel backlight power circuit.
Page 16
Chapter 2 LPC Interface Signals Signal Pin# Pin Type Pwr Rail /Tolerance BT700 Carrier Board Description LPC_AD[0..3] Multiplexed Command, Address and Data. 185-188 I/O CMOS 3.3V/3.3V Connect to LPC device GPIO[0..3] General purpose input/output [0..3] LPC_FRAME# LPC frame indicates the start of a new cycle or the termination of a broken cycle.
Page 17
Manufacturing Signals Signal Pin# Pin Type Pwr Rail /Tolerance BT700 Carrier Board Description This pin is reserved for manufacturing and debugging purposes. MFG_NC0 May be used as JTAG_TCK signal for boundary scan purposes during production or as a vendor specific control signal. When used as a vendor specific control signal the multiplexer must be controlled by the MFG_NC4 signal.
Installing BT700 onto a Carrier Board 3. Press down BT700 and put on the heat sink on top of BT700 with its mounting holes and bolts aligned on the carrier board. Use the mounting screws to fix BT700 and heat sink in place.
Chapter 3 Chapter 3 - BIOS Setup Legends Overview KEYs Function The BIOS is a program that takes care of the basic level of communication between the CPU Right and Left Arrows Moves the highlight left or right to select a and peripherals.
Chapter 3 AMI BIOS Setup Utility Advanced Main The Advanced menu allows you to configure your system for basic operation. Some entries are defaults required by the system board, while others, if enabled, will improve the performance of your system or let you set some features according to your preference. The Main menu is the first screen that you will see when you enter the BIOS Setup Utility.
Page 21
Chapter 3 PC Health Status CPU Configuration This section only displays the hardware health monitor. This section is used to configure the CPU. It will also display the detection of CPU information. Aptio Setup Utility - Copyright (C) 2013 American Megatrends, Inc. Aptio Setup Utility - Copyright (C) 2013 American Megatrends, Inc.
Page 22
Chapter 3 SATA Configuration LPSS & SCC Configuration This section is used to configure the settings of SATA device. This section is used to configure the LPSS & SCC settings. Aptio Setup Utility - Copyright (C) 2013 American Megatrends, Inc. Aptio Setup Utility - Copyright (C) 2013 American Megatrends, Inc.
Page 23
Chapter 3 Network Stack Configuration Ipv4 PXE Support This section is used to enable or disable UEFI network stack. When enabled, Ipv4 PXE boot supports. When disabled, Ipv4 PXE boot option will not be created. Aptio Setup Utility - Copyright (C) 2013 American Megatrends, Inc. Ipv6 PXE Support Advanced Network Stack...
Page 24
Chapter 3 CSM Configuration Trusted Computing This section configures the CSM settings. This section configures settings relevant to Trusted Computing innovations. Aptio Setup Utility - Copyright (C) 2013 American Megatrends, Inc. Aptio Setup Utility - Copyright (C) 2013 American Megatrends, Inc. Advanced Advanced Enables or Disables...
Page 25
USB type in table 2 below. Version 2.16.1242 Copyright (C) 2013 American Megatrends, Inc. Table 2. The Type of USB Ports Legacy USB Support Enabled Model Name BT700 Enable legacy USB. Native Auto USB 3.0 (share with USB 2.0 port 6 and 7)* Disable support for legacy when no USB devices are connected.
Page 26
Chapter 3 Security Configuration Intel(R) I210 Gigabit Network Connection - 00:A0:C9:00:... This section only displays the setting relevant to the Intel(R) Anti-Theft Technology. This section is used to configure the parameters of Gigabit Ethernet device. Aptio Setup Utility - Copyright (C) 2013 American Megatrends, Inc. Aptio Setup Utility - Copyright (C) 2013 American Megatrends, Inc.
Chapter 3 Chipset NIC Configuration This field is used to configure the network device. The section configures the relevant functions of chipset. Aptio Setup Utility - Copyright (C) 2013 American Megatrends, Inc. Aptio Setup Utility - Copyright (C) 2013 American Megatrends, Inc. Advanced Main Advanced...
Page 28
Chapter 3 North Bridge Intel IGD Configuration This section configures the North bridge parameters. Aptio Setup Utility - Copyright (C) 2013 American Megatrends, Inc. Chipset Aptio Setup Utility - Copyright (C) 2013 American Megatrends, Inc. GOP Information Chipset Intel(R) GOP Driver [N/A] ...
Page 29
Chapter 3 LCD Control LCD Panel Type Select the LCD panel used by Internal Graphics Device by selecting the appropriate Aptio Setup Utility - Copyright (C) 2013 American Megatrends, Inc. setup item. Please refer to the screen shown below. Chipset LCD Control Select the Video Device which will be activated...
Page 30
Chapter 3 South Bridge Memory Configuration This field is used to configure the parameters of the South Bridge. Aptio Setup Utility - Copyright (C) 2013 American Megatrends, Inc. Chipset Aptio Setup Utility - Copyright (C) 2013 American Megatrends, Inc. Memory Information Total Memory 2048 MB (LPDDR3) Chipset...
Page 31
Chapter 3 Azalia HD Audio PCI Express Configuration This section configues Azalia HD Audio options. This section configues settings relevant to PCI Express devices. Aptio Setup Utility - Copyright (C) 2013 American Megatrends, Inc. Aptio Setup Utility - Copyright (C) 2013 American Megatrends, Inc. Chipset Chipset Control Detection of the...
Chapter 3 Save & Exit Updating the BIOS To update the BIOS, you will need the new BIOS file and a flash utility, AFUDOS.EXE. Please contact technical support or your sales representative for the files. Aptio Setup Utility - Copyright (C) 2013 American Megatrends, Inc. Main Advanced Chipset...
Chapter 3 Notice: BIOS SPI ROM 1. The Intel Management Engine has already been integrated into this system board. Due to ® the safety concerns, the BIOS (SPI ROM) chip cannot be removed from this system board and used on another system board of the same model. 2.
Chapter 4 Chapter 4 - Supported Software For Windows 7 The CD that came with the system board contains drivers, utilities and software applications required to enhance the performance of the system board. Insert the CD into a CD-ROM drive. The autorun screen (Mainboard Utility CD) will appear. If after inserting the CD, “Autorun”...
Chapter 4 Intel Chipset Software Installation Utility 3. Go through the readme docu- ment for more installation tips then click Next. The Intel Chipset Device Software is used for updating Windows ® INF files so that the Intel chipset can be recognized and configured properly in the system. To install the utility, click “Intel Chipset Software Installation Utility”...
Page 37
Chapter 4 Intel HD Graphics Drivers 3. Go through the readme docu- ment for system requirements and installation tips then click To install the driver, click “Intel HD Graphics Drivers” on the main menu. Next. 1. Setup is now ready to install the graphics driver.
Chapter 4 Intel LAN Drivers 4. Click Install to begin the installation. To install the driver, click “Intel LAN Drivers” on the main menu. 1. Setup is ready to install the driver. Click Next. 5. After completing installa- tion, click Finish. 2.
Page 39
Chapter 4 Kernel Mode Driver Framework (For Windows 7 only) Intel Trusted Execution Engine Driver To install the driver, click “Kernel Mode Driver Framework” on the main menu. To install the driver, click “Intel Trusted Execution Engine Driver” on the main menu. 1.
Chapter 4 3. The step displays the Realtek Audio Drivers installing status in the progress. To install the driver, click “Realtek Audio Drivers” on the main menu 1. Setup is now ready to install the audio driver. Click Next. 2. Follow the remainder of the steps on the screen;...
Page 41
Chapter 4 Intel Sideband Fabric Device (MBI) Driver 3. The step performs setup operations. Click “Next“ to (For Windows 8 only) continue. To install the driver, click “Intel Sideband Fabric Device (MBI) Driver” on the main menu. 1. The setup program will be installed.
Chapter 4 DFI Utility 3. Click Install to begin the installation. DFI Utility provides information about the board, HW Health, Watchdog, DIO, and Backlight. To access the utility, click “DFI Utility” on the main menu. Note: If you are using Windows 7, you need to access the operating system as an administrator to be able to install the utility.
Page 43
Chapter 4 The DFI Utility icon will appear on the desktop. Double-click the icon to open the utility. Information HW Health Set HW Health Backlight Chapter 4 Supported Software www.dfi .com...
Page 44
Chapter 4 Infineon TPM Driver and Tool (option) To install the driver, click “Infineon TPM driver and tool (option)” on the main menu. 1. The setup program is preparing to install the driver. WatchDog 2. The setup program is now ready to install the utility.
Page 45
Chapter 4 4. Enter the necessary information 7. TPM requires installing the Micro- and then click Next. soft Visual C++ package prior to installing the utility. Click Install. 5. Select a setup type and then click 8. The setup program is currently Next.
Page 46
Chapter 4 10. Click “Yes“ to restart your system. Intel USB 3.0 Drivers (For Windows 7 Only) To install the driver, click “Intel USB 3.0 Driver” on the main menu. 1. Setup is ready to install the driver. Click Next. 2.
Page 47
Chapter 4 3. Go through the readme docu- IO Driver Patch (For Windows 7 - 64bit Only) ment for more installation tips then click Next. To install the driver, click “IO Driver Patch” on the main menu. Note: When you have problems in using the IO Driver on Windows 7 - 64bit, you need to follow the setps to install the IO Driver Patch.
Page 48
Chapter 4 IO Driver 3. Choose the setup type and then click “Next”. To install the driver, click “IO Driver” on the main menu. Before you install the IO Driver, read the install message and then click “OK”. 1. The setup program is preparing to install the driver.
Page 49
Chapter 4 5. The installation has been com- Adobe Acrobat Reader 9.3 pleted successfully. Click “Finish“ to exit the wizard. To install the reader, click “Adobe Acrobat Reader 9.3” on the main menu. 1. Click Next to install or click Change Destination Folder to select another folder.
Appendix A Appendix A - System Error Message When the BIOS encounters an error that requires the user to correct something, either a beep code will sound or a message will be displayed in a box in the middle of the screen and the message, PRESS F1 TO CONTINUE, CTRL-ALT-ESC or DEL TO ENTER SETUP, will be shown in the information box at the bottom.
Appendix B Appendix B - Troubleshooting The picture seems to be constantly moving. 1. The monitor has lost its vertical sync. Adjust the monitor’s vertical sync. Troubleshooting Checklist 2. Move away any objects, such as another monitor or fan, that may be creating a magnetic This chapter of the manual is designed to help you with problems that you may encounter field around the display.
Appendix B Hard Drive System Board 1. Make sure the add-in card is seated securely in the expansion slot. If the add-in card is Hard disk failure. loose, power off the system, re-install the card and power up the system. 1.