Function Key - Sony BVM-E251 Operating Instructions Manual

Submenu Setting
[SDCP/SDAP Sets the SDCP/SDAP community
Community] name.
When the item is selected, you can enter
the community name (four characters).
[SONY]: SONY is entered as a

community name.
[New Name]: Enter a new name.

[SDCP Port No] Sets the SDCP port number.
Set from 53434 to 53534. (Default value:
[53484])
[SDAP Port No] Sets the SDAP port number.
Set from 53812 to 53912. (Default value:
[53862])
[SDAP Broadcast] Sets whether or not to issue the SDAP
([Disable] or [Enable]).
[SDAP Broadcast Sets the period (seconds) to issue the
Period] SDAP.
Set from 05 to 30. (Default value: [30])
[Reset Protocol Resets the protocol setting.
Setting] When the item is selected, the following
message appears.
[Are you sure ?]
[OK]: To reset data, press the

ENTER (Ent) button.
[Cancel]: To cancel, press the

MENU button.

[Function Key]

Assigns the function to the function buttons of the
controller.
For details on the function assignment, see "Assigning a
Function to a Function Button" (page 72).
Notes
Use the BKM-16R with software version 1.6 or higher

or BKM-17R to assign [Status], [Center Marker],
[Aspect Marker-Line], [Aspect Blanking-Half],
[Aspect Blanking-Black], [Difference], [Horopter
Check], [Flip H].
 Use the BKM-16R with software version 1.5 or higher
or BKM-17R to assign [Checkerboard] and [L/R
Switch].
Use the BKM-16R with software version 1.4 or higher

or BKM-17R to assign [Audio Level Meter], [ALM
Hold Reset] and [Time Code].
 Use the BKM-16R with software version 1.3 or higher
or BKM-17R to assign [Black Detail Mode].
Use the BKM-17R to assign [Flicker Free].

Submenu Setting
[F1]-[F16] The following functions are assigned.
[Scan Mode]: Changes the scan

mode of the picture.
[Native Scan]: Displays the picture

in native scan mode.
Submenu Setting
[16:9]: Changes the aspect ratio to

16:9 or 1.896:1 (digital cinema
signal), and when set to Off, the
aspect ratio changes to 4:3 or 2.39:1.
The aspect ratio of some signals is
fixed to 16:9 depending on the signal
format.
For details, see "Available Signal
Formats" on page 88.
[H Delay]: The picture moves

horizontally and a horizontal sync
signal appears. Brightness of the
picture increases automatically, and
makes it easy to check the sync part.
When the V Delay button is set to on
in H delay mode, a pulse cross
picture is displayed.
[V Delay]: The picture moves

vertically and a vertical sync signal
appears approximately in the center
of the screen. The brightness of the
picture increases automatically, and
makes it easy to check the sync part.
When the H Delay button is set to
on in V delay mode, a pulse cross
picture is displayed.
[External Sync]

not to set to the external sync mode
when the analog component signal
or analog RGB signal is input.
When the button is set to on, the
signal to be displayed is
synchronized with the sync signal
input to the EXT SYNC connector
(External Sync). When set to off, the
signal to be displayed is
synchronized with the sync signal
included in the signals being
monitored (Internal Sync).
Note
When the button is set to off (Internal
Sync), a sync signal is added on the Y
signal to monitor the analog
component signal and on the G signal
to monitor the analog RGB signal.
[Comb]

on. When the button is set to off, the
trap·band-pass filter is selected.
When the displayed signal is NTSC,
PAL, or PAL-M, this functions.
[Char Off]: The characters on the

monitor screen hide during manual
adjustment.
[Color Temp]: You can directly

access the [Manual Adjust] menu of
the [Color Temp Adj] menu.
1)
: Sets whether or
1)
: The comb filter is turned
71
Adjustment Using the Menus