Sony BVM-E251 Operating Instructions Manual page 53

Submenu Setting
[SDI RGB 10bit] [Upper Limit] (upper limit)
[G]: 0000 to 1023 (Default value:

[0983])
[B]: 0000 to 1023 (Default value:

[0983])
[R]: 0000 to 1023 (Default value:

[0983])
[Lower Limit] (lower limit)
[G]: 0000 to 1023 (Default value:

[0020])
[B]: 0000 to 1023 (Default value:

[0020])
[R]: 0000 to 1023 (Default value:

[0020])
[SDI YCbCr 12bit] [Upper Limit] (upper limit)
[Y]: 0000 to 4095 (Default value:

[3935])
[Cb]: 0000 to 4095 (Default value:

[4019])
[Cr]: 0000 to 4095 (Default value:

[4019])
[Lower Limit] (lower limit)
[Y]: 0000 to 4095 (Default value:

[0080])
[Cb]: 0000 to 4095 (Default value:

[0077])
[Cr]: 0000 to 4095 (Default value:

[0077])
[SDI RGB 12bit] [Upper Limit] (upper limit)
[G]: 0000 to 4095 (Default value:

[3935])
[B]: 0000 to 4095 (Default value:

[3935])
[R]: 0000 to 4095 (Default value:

[3935])
[Lower Limit] (lower limit)
[G]: 0000 to 4095 (Default value:

[0080])
[B]: 0000 to 4095 (Default value:

[0080])
[R]: 0000 to 4095 (Default value:

[0080])
[HDMI YCbCr] [Upper Limit] (upper limit)
[Y]: 0000 to 4095 (Default value:

[3935]) (12bit conversion value)
[Cb]: 0000 to 4095 (Default value:

[4019]) (12bit conversion value)
[Cr]: 0000 to 4095 (Default value:

[4019]) (12bit conversion value)
[Lower Limit] (lower limit)
[Y]: 0000 to 4095 (Default value:

[0080]) (12bit conversion value)
[Cb]: 0000 to 4095 (Default value:

[0077]) (12bit conversion value)
[Cr]: 0000 to 4095 (Default value:

[0077]) (12bit conversion value)
Submenu Setting
[HDMI RGB] [Upper Limit] (upper limit)
[G]: 0000 to 4095 (Default value:

[3935]) (12bit conversion value)
[B]: 0000 to 4095 (Default value:

[3935]) (12bit conversion value)
[R]: 0000 to 4095 (Default value:

[3935]) (12bit conversion value)
[Lower Limit] (lower limit)
[G]: 0000 to 4095 (Default value:

[0080]) (12bit conversion value)
[B]: 0000 to 4095 (Default value:

[0080]) (12bit conversion value)
[R]: 0000 to 4095 (Default value:

[0080]) (12bit conversion value)
[Post-Process Detection]
Sets the error detection setting for the signal after YCbCr
is converted to RGB.
Submenu Setting
[Detection] Sets whether or not to detect the error
of the input signal ([Off] or [On]).
[Pixel Threshold] Sets the pixel number of the gamut
error in the frame to notify the gamut
error detection.
When the pixel number of the error is
over the set pixel number, the detection
is notified. Set to 00000 to 65535.
(Default value: [00000])
[Signal Level] Sets the upper and lower lines of the
signal level.
The signal level to be set is black level
256 and white level 3760 in 12bit
conversion value.
[Upper Limit] (upper limit): 0000

to 4095 (Default value: [3761])
[Lower Limit] (lower limit): 0000

to 4095 (Default value: [0255])
[Zebra Pattern]
Sets the zebra pattern displayed by the gamut error
detection.
Submenu Setting
[Line] Sets the direction of the pattern.
[Diagonal Type1]: Right

descending
[Diagonal Type2]: Left descending

[Modulation] Sets the amplitude of the pattern
display.
Set to 1 to 50. (Default value: [16])
Note
Depending on the Gamma settings and input signal
levels that you are selecting, the zebra pattern is not
displayed. Set to a larger value in the [Modulation]
menu.
53
Adjustment Using the Menus