Sony BVM-E251 Operating Instructions Manual page 37

Submenu Setting
[Picture Preset] Sets the picture adjustment preset.
Select from the following:
[Preset1] to [Preset5]

[Preset(DCI)]

[Matrix/Color Sets [Matrix] data (transmission
Profile] matrix) and [Color Profile] depending
on the input signal format.
For details of the setting, see [Matrix/
Color Profile] (page 38).
[Marker Preset] Sets the marker preset data.
You can select from [Marker1] to
[Marker5]. (Default value: [Marker1])
For setting the marker, see the [Marker
Setting] menu (page 46) of the [Function
Setting] menu.
[H Shift Offset] Sets the horizontal picture position
when the analog signal is input.
You can select when [Format] is set to
[Composite Auto], [Composite NTSC],
[Composite PAL], or [Composite PAL-
M].
Set to –100 to +100
[000])
1) When the setting value is out of
range, the display of the setting value
is changed but the horizontal
position of the picture is not
changed.
To hide the characters on the monitor
during adjustment
Set the CHAR OFF button of the
controller to on. As the characters on
the display are hidden, it becomes easy
to adjust the picture. To display the
characters, set the CHAR OFF button to
off.
[Channel Name] Sets a channel name.
When the item is selected, you can
select a preset name or enter a new one.
[PROG___]: Program signal

[EDIT___]: Signal from an editor

[CAM___]: Camera signal

[VTR___]: Signal from a VTR

[PREV___]: Preview monitor

[New Name]: Enter a new name.

(Up to 20 characters can be entered.)
[NTSC Setup Level] Sets the NTSC setup level.
You can select when [Format] is set to
[Composite Auto] or [Composite
NTSC].
[0%]

[7.5%]

[RGB/YCC Range] Sets the quantization range of the 4:4:4
RGB SDI or HDMI input signal.
For details of the setting, see [RGB/YCC
Range] (page 44).
Submenu
[1080I/PsF]
1)
. (Default value:
[Film Cadence]
Setting
When the 1080i/PsF signal is input,
select the display mode.
You can select when [Format] is set to
[3G/HD/SD-SDI Auto], [HD/SD-SDI
Auto], [4:2:2 YCbCr 10bit], [4:4:4
YCbCr 10bit], [4:4:4 RGB 10bit], [4:4:4
YCbCr 12bit], [4:4:4 RGB 12bit], or
[4:4:4 XYZ 12bit].
When [1080I] is selected, the I/P
conversion signal is displayed. When
[1080PsF] is selected, the progressive
conversion (PsF to P) signal is
displayed.
When the 1080PsF signal is input and
[1080I] is selected, the display delay is
shortened. The signal converted from
PsF to P is not displayed and the I/P
conversion signal is displayed.
When [Format] is set to [3G/HD/SD-
SDI Auto] and Payload ID data are
superimposed on the SDI signal, 1080i/
PsF processing is performed based on
the Payload ID data, regardless of the
setting value.
For details of the setting, see [1080I/PsF]
(page 44).
Sets the film cadence mode.
The progressive conversion signal is
displayed according to the setting.
[Off]: The progressive conversion

signal is not displayed in film
cadence mode
[2-2]: The progressive conversion

signal is displayed when the interlace
signal of 2-2 pull-down processing is
input
[2-3]: The progressive conversion

signal is displayed when the interlace
signal of 2-3 pull-down processing is
input
[2-3-3-2]: The progressive

conversion signal is displayed when
the interlace signal of 2-3-3-2 pull-
down processing is input
Notes
When the 50i interlace signal is

input, the mode is automatically set
to [2-2] even when [2-3] or [2-3-3-2]
is selected.
The signal is not displayed in film

cadence mode when the 1080i
interlace signal is input and
[1080PsF] is selected in the [1080I/
PsF] menu. Set to [1080I].
As the signal is displayed in film

cadence mode by cadence sequence
detection based on the pattern of the
input signal, the signal may not be
displayed correctly because of the
pattern of the input signal.
The signal is not displayed in the

film cadence mode when [Side by
Side], [Wipe], [Butterfly], or
[Blending] is set to [On].
Adjustment Using the Menus
37