Sony BVM-E251 Operating Instructions Manual page 32

[Manual Adjust]
Adjusts values by turning the PHASE, CHROMA,
BRIGHT, and/or CONTRAST knobs. After adjustment,
press the ENTER (Ent) button to confirm the adjusted
values.
 [Phase]: –150 to +150 (Default value: [000])
 [Chroma]: 0000 to 2000 (Default value: [1000])
[Bright]: –500 to +500 (Default value: [000])

[Contrast]: 0000 to 2500 (Default value: [1000] (for

[Preset1] to [Preset5]), Default value: [0480] (for
[Preset(DCI)]))
To display no characters on the screen while
adjusting manually
Set the CHAR OFF button to on. The characters
disappear. To display characters, set the CHAR OFF
button to off.
To reset the setting to the default
Press the corresponding MANUAL button. The
adjusted value is reset to the default.
To cancel adjustment
Press the MENU button. The adjustment data is
cleared.
To confirm adjustment
Press the ENTER (Ent) button.
Note
During adjustment, the screen saver is activated
automatically if the operating conditions are met
regardless of the setting of the screen saver function.
[Copy From]
Copies picture adjustment preset data.
Notes
Automatic adjustment data is not copied.

Use the BKM-16R with software version 1.6 or higher

or BKM-17R to use the [Copy From] function.
Submenu Setting
[Preset Value] Copies other data in this monitor.
When the item is selected, you can
select from [Preset1], [Preset2],
[Preset3], [Preset4], [Preset5], or
[Preset(DCI)].
[Other Monitor] Copies data from another monitor.
Note
Use the BVM-E251/BVM-E171 as a
source monitor to use the [Other
Monitor] function.
[Monitor ID] Enter the ID number of the source
monitor.
When the NETWORK switch is set to
PEER TO PEER, this is not selectable.
When the ID number is entered, you
can select from [Preset1], [Preset2],
[Preset3], [Preset4], [Preset5], or
[Preset(DCI)].
32
Adjustment Using the Menus
Submenu Setting
[External Memory] Copies data in the USB memory stick,
etc.
Note
Use the USB memory stick, etc. with
data stored by the BVM-E251/BVM-
E171 to use the [External Memory]
function.
When the item is selected, the file
names in the source USB memory stick,
etc. are displayed.
When the file is selected, you can select
from [Preset1], [Preset2], [Preset3],
[Preset4], [Preset5], or [Preset(DCI)].
[Color Temp Adj]
Adjusts the color temperature.
When the item is selected, the color temperature data to
be adjusted is displayed.
 Except for the XYZ format signal
When [D93], [D65], [D61], [D55], or [DCI] data is
changed, they are displayed as [D93*], [D65*], [D61*],
[D55*], or [DCI*].
To change the color temperature data to be adjusted,
select [D93], [D65], [D61], [D55], [DCI], [User1],
[User2], [User3], [User4], or [User5] in the [Color
Temp] menu of the [Channel Configuration] menu.
 For the XYZ format signal
When [DCI XYZ] data is changed, it is displayed as
[DCI XYZ*].
To change the color temperature data to be adjusted,
select [DCI XYZ], [User XYZ1], [User XYZ2], [User
XYZ3], [User XYZ4], or [User XYZ5] in the [Color
Temp] menu (page 36) of the [Channel
Configuration] menu.
Note
If you measure the color temperatures of different
display types, such as CRT, LCD, or OLED, by using a
common (or general) color analyzer that is based on CIE
1931, and adjust the xy chromaticity to the same value,
the appearance may be different because of optical
spectrum differences.
To compensate for this difference, the [D93], [D65],
[D61], [D55], and [User1] to [User5] settings (except
DCI) of the monitor are adjusted by an offset
1) The offset value applied (x-0.006, y-0.011) is based on the
Judd's function to the CIE 1931 (x, y) value.
[Manual]
Adjusts the color temperature manually.
When the item is selected, the color temperature data to
be set is displayed.
Except for the XYZ format signal
1)
.