Advertisement
Quick Links
Advertisement
Related Manuals for ACME Stage Blinder IP BL-200 WW
Summary of Contents for ACME Stage Blinder IP BL-200 WW
- Page 1 BL-200 WW BL-200 CW...
- Page 2 Menu 1. Safety Instructions ..........................2 2. Technical Specifications ........................3 3. Installation and Connection ......................4 4. How to set the unit ...........................5 4.1 Rear Panel ............................5 4.2 Main Function..........................6 5. How to control the unit ........................10 6. DMX512 configuration ........................11 7. DMX512 Connection........................12 8.Troubleshooting ..........................12 9.
- Page 3 1. Safety Instructions Please read the instruction carefully which includes important information about the installation, usage and maintenance. WARNING Please keep this User Manual for future consultation. If you sell the fixture to another user, be sure that they also receive this instruction booklet. ...
- Page 4 2. Technical Specifications 4 channel Mode switchable : 1 /2 /4 /6 Channel Modes; Dimmer, Strobe; Ideal for discotheques, clubs, bars, parties, Mobile DJs, etc. Input Voltage: AC100V~240V，50/60Hz Total Power consumption: 235W Beam Angle: 50°...
- Page 5 Installation and Connection The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.
- Page 6 Fixture jointing (Between more than two units) Warning: Max. load≤10 fixtures vertical. 4. How to set the unit 4.1 Rear Panel ○ 1 DMX input/output: For DMX512 link, use 3-pin XLR plug cable to input DMX signal, and to link the next unit.
- Page 7 ○ 2 LED indicator： POWER Power On DMX input present ○ 3 Button： MENU To select the programming functions DOWN To go forward in the selected functions To go backward in the selected functions ENTER To confirm the selected functions ○...
- Page 8 DMX 512 Address Setting Select the , press the ENTER button and the display will blink. Use the DOWN and UP button to change the DMX 512 address （ 001-512） . Once the address has been selected, press the ENTER button to setup or exit menu mode without any change after 8 seconds automatically.
- Page 9 or move). Once selected, press the ENTER button to setup or exit menu mode without any change after 8 seconds. Back to the functions without any change press the MENU button again. Dimmer Mode Select the , press the ENTER button. Use the DOWN and UP button to select (Dimmer Mode 1)…...
- Page 10 Select the , press the ENTER button. Use the DOWN and UP button to select (Blackout) , (Hold the last state)or (Manual mode). Once selected, press the ENTER button to setup or exit menu mode without any change after 8 seconds. Back to the functions without any change press the MENU button again.
- Page 11 . To go back to the functions press the MENU button. Fixture Hour Select the , press ENTER button and the display will show the number of working hours of the unit. To go back to the functions press the MENU button. Software Version Select the , press ENTER button and the display will show the version of software of the unit.
- Page 12 6. DMX512 configuration Channel Mode：...
- Page 13 7. DMX512 Connection Mode connection： 1. Connect the fixture together in a “daisy chain” by XLR plug cable from the output of the fixture to the input of the next fixture. The cable cannot be branched or split to a “Y” cable. Inadequate or damaged cables, soldered joints or corroded connectors can easily distort the signal and shut down the system 2.
- Page 14 B. Not responding to DMX controller 1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly. 2. If the DMX LED is on and no response to the channel, check the address settings and DMX polarity. 3.
- Page 16 Declaration of Conformity We declare that our products (lighting equipments) comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility (EMC) Directive 89/336/EEC. EN55103-1: 2009+A1:2012; EN55103-2: 2009; EN61000-3-2: 2014; EN61000-3-3: 2013. & Harmonized Standard EN 60598-1:2015;...
Need help?
Do you have a question about the Stage Blinder IP BL-200 WW and is the answer not in the manual?
Questions and answers