This controller control DMA transfer of the data transferred through the input interfaces such as the USB and expansion card slot as well as DMA transfer of the

data stored in the DIMM.

Image data generation/output function

This function generates image data for color printing from the received image data and the mask pattern (corresponding to print mode) stored in the DIMM, and

stored the generated image data in another DIMM. It also outputs the generated image data to the carriage PCB.

Interrupt controller

This controller receives and processes internal interrupts and external interrupts from the USB, image processing unit, and expansion card slot.

Timer function

Even when the printer is turned off, the timer function is held on using the RTC and lithium battery to assist the cleaning function.

When the power cord is plugged to the outlet, power is supplied to the RTC and therefore the lithium secondary battery power is not consumed.

Heat Enable signal control function

This function uses the pulse width to perform variable control of the time of application of the Heat Enable signal to the nozzle heater board for each printhead

nozzle array.

Linear scale count function

This function reads the linear scale when the carriage moves, thus generating the ink discharge timing. It also counts the linear scale timing cycle using the reference

clock to measure the carriage moving speed.

Dot count function

This function controls the discharge dots used as the information for Heat Enable signal control, maintenance jet control, cleaning control, and remaining ink level

for each nozzle array.

Operation panel control function

This function controls serial communication with the operation panel.

PWM control function

This function controls driving of the suction fan and mist fan as well as the temperature of the printhead.

Remaining ink level detection function

This function detects the remaining level of each color of ink based on the signal received from the hollow needle mounted in the ink tank unit.

LED control function

This function controls the LEDs on the ink tank unit.

I/O port function

This function controls input signals from sensors.

Power ON/OFF control function

This function controls turning on/off of the drive power (26 V and 21.5 V) supplied from the power supply PCB.

Head DI sensor read control function

This function controls read operation by the head DI sensor.

Multi sensor control function

This function controls the LED, adjusts the gain, and controls obtainment of the reading for the multi sensor.

EEPROM control function

This function controls the EEPROMs of individual ink tanks, the maintenance cartridge EEPROM, the EEPROM on the maintenance cartridge relay PCB, and the

head EEPROM in addition to the on-board EEPROM.

Motor control function

This function controls the carriage motor, feed motor, valve motor, spur motor, pump motor, cassette motor, lift motor, cutter motor, and roll motor based on the

input signals from sensors.

b) Driver IC (IC3101)

This IC generates a carriage motor control signal based on the control signal from the ASIC.

c) Driver IC (IC2801)

This IC generates feed motor, valve motor, and spur motor control signals based on the control signal from the ASIC.

d) Driver IC (IC2901)

This IC generates pump motor and cassette motor control signals based on the control signal from the ASIC.

e) Driver IC (IC3001)

This IC generates a lift motor control signal based on the control signal from the ASIC.

f) Regulator IC (IC3301)

This IC generates the 3.3 V to be supplied to the tank ROM board.

g) DIMMs (IC301,IC302,IC601,IC602)

The DIMM comprising a 128-MB DDR-SDRAM and a 64-MB SDR-SDRAM is connected to the 32-bit data bus to be used as a work area.

During print data reception, it is also used as an image buffer.

It cannot be expanded.

h) FLASH ROM (IC701)

A 64-MB flash ROM is connected to the 8-bit data bus to store the printer control program.

i) EEPROM (IC802)

The 128-KB EEPROM stores various setting values, adjustment values, log data, counter values related to the user/servicing.

MEMO:

After replacement of the main controller PCB, the printer must be started up in the service mode to take over the setting and adjustment values to the new PCB

properly (the service mode will be switched to the PCB replacement mode automatically).

2-58

Table of Contents