Midi Transpose; Midi Filter - Korg Ci-9600 Owner's Manual

3. Select a "Sync." radio button
Press either the "Int." or the "Ext." radio button.
"Int.": The internal clock will be used.
Select "Int." when you are using the Ci-
9600/Ci-8600 by itself, or when using it as
the master (controlling device) to synchro-
nize external MIDI devices to the MIDI
clock transmitted by the Ci-9600/Ci-8600.
"Ext.": The Ci-9600/Ci-8600's recorder will oper-
ate in synchronization with the MIDI clock
messages it receives. Select "Ext." when
you are using the Ci-9600/Ci-8600 as a
slave device (the device being controlled)
that is synchronized to the MIDI clock
transmitted from an external device.
To write settings into internal memory
In the "Func 10/13" page, execute "Write."
If you turn off the power without writing, the
previous settings will reappear.
To return to the previous display
If you press the [EXIT] switch or the [FUNC-
TION] switch, the [FUNCTION] switch indica-
tor will go dark, and you will return to the
previous LCD screen.

MIDI Transpose

You can specify whether the "Transpose" setting of
the "Func 1/13" page will be applied to the data
that is transmitted or received via MIDI.
1. Press the [FUNCTION] switch
2. Access the "Func 7/13" page
3. Select one of the "MIDI Transpose" radio buttons
Press either the "Tx" or "Rx" radio button.
"Tx": Transpose will be applied to the trans-
mitted note data.
It will not affect the received note data.
"Rx": Transpose will be applied to the received
note data.
It will not affect the transmitted note data.

MIDI Filter

You can specify whether or not each type of MIDI
message (e.g., program change, control change)
will be transmitted and received.
1. Press the [FUNCTION] switch
2. Access the "Func 8/13" page
3. For the types of MIDI message that you do not
wish to transmit or receive, select the corre-
sponding check box to turn it off
"Prog": Program change
Programs of a connected MIDI device can be
changed by transmitting program changes
from the Ci-9600/Ci-8600.
When a program change number is received
from an external device, sound will be selected
on the Ci-9600/Ci-8600 as shown in the tables
on p.97–.
To allow these messages to be transmitted and
received, turn on the "Prog." check box. To pre-
vent these messages from being transmitted or
received, turn off the "Prog." check box.
"Prog Bank": Program bank change
If you want MIDI program bank messages to be
transmitted and received, turn on the "Prog
Bank" check box. If you do not want these mes-
sages to be transmitted or received, turn off the
"Prog Bank" check box.
"Control": Control change
These messages transmit data such as the Ci-
9600/Ci-8600's damper pedal operation to an
external MIDI device to control it, or receive
damper pedal and other messages from an
external MIDI device to control the Ci-9600/Ci-
8600. If you wish to transmit/receive these
messages, turn the "Control" check box on. If
you do not want to transmit/receive these mes-
sages, turn the "Control" check box off.
Control changes from an external device will
always affect both sounds even in Layer or Split
mode, regardless of the pedal settings of the Ci-
9600/Ci-8600 itself. (☞p.28 "Damper pedal set-
tings for Layer and Split")
"After Touch"
If you want MIDI aftertouch messages to be
transmitted and received, turn on the "After
Touch" check box. If you do not want these
messages to be transmitted or received, turn off
the "After Touch" check box.
"Exclusive"
If you want MIDI exclusive messages to be
transmitted and received, turn on the "Exclu-
sive " check box. If you do not want these mes-
sages to be transmitted or received, turn off the
"Exclusive" check box.
To write settings into internal memory
In the "Func 10/13" page, execute "Write."
If you turn off the power without writing, the
previous settings will reappear.
To return to the previous display
If you press the [EXIT] switch or the [FUNC-
TION] switch, the [FUNCTION] switch indica-
tor will go dark, and you will return to the
previous LCD screen.
89