CipherLab 5000 Hardware Manual
  1. Manuals
  2. Brands
  3. CipherLab Manuals
  4. Storage
  5. 5000
  6. Hardware manual
CipherLab 5000 Hardware Manual

CipherLab 5000 Hardware Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

CipherLab
5000/5100
Hardware Manual
Version 1.02
Sep. 13, 06

Advertisement

Table of Contents
loading

Summary of Contents for CipherLab 5000

  • Page 1 CipherLab 5000/5100 Hardware Manual Version 1.02 Sep. 13, 06...
  • Page 2 Reserved. This page is a reverse of the preceding page; they are for identifying a draft version. When the document is converted to PDF, they are to be replaced by the designed cover and a blank page. To identify version of a PDF document, use the stamp tool. (Draft / Final / For Public Release / Revised …...

  • Page 3: Disclaimer Of Liability

    TATEMENTS Copyright © Syntech Information Co., Ltd. 2004 All rights reserved. This document, as well as any software included, may not be reproduced, stored in retrieval system or transmitted, in any form or by any means, without prior written consent of the copyright owners. Trademark logo is a registered trademark of Syntech Information Co., Ltd.
  • Page 4 Statements: FCC Regulations & Technical Standards FCC Regulations This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

  • Page 5: Table Of Contents

    REFACE & M ................1 AINTENANCE ..................2 ETTING EADY 1. I 5000/5100 ............... 3 NTRODUCING 1.1 Product Highlights ..................... 3 1.2 Nomenclature...................... 4 1.2.1 Inside Enclosures ..................5 1.2.2 Dimensions....................6 1.3 Features ......................7 1.3.1 Power ......................7 1.3.2 CPU......................
  • Page 6 Contents: Section 2 ~4.3 2. I 5000/5100 ................ 23 NSTALLING 2.1 Setting up the terminal ..................23 2.2 Wiring........................ 28 2.2.1 Pin Assignments..................29 2.2.2 RS-232 ...................... 31 2.2.3 RS-485 ...................... 32 2.2.4 Digital Inputs/Outputs ................34 3. S ............... 35...
  • Page 7 4.5 Kernel Menu ..................... 65 4.5.1 Information ....................66 4.5.2 Load Program.................... 67 4.5.3 Kernel Update ................... 68 4.5.4 Test & Calibrate..................68 5. M 5000/5100 ................. 69 ANAGING 5.1 For proprietary applications ................70 5.2 For custom applications ................... 70 ..................71 PECIFICATIONS .................
  • Page 9 Contents: Tables Table 1: Power consumption................8 Table 2: Memory explained ................10 Table 3: Keypad explained................. 12 Table 4: Display formats..................13 Table 5: Types of readers .................. 14 Table 6: Decide resistance value ............... 15 Table 7: Optional accessories ................22 Table 8: Stages of installation ................
  • Page 10 Contents: Figures Figure 1: References for setting up system............2 Figure 2: Nomenclature of terminal ..............4 Figure 3: Components inside terminal..............5 Figure 4: Physical dimensions................6 Figure 5: Installing battery pack ................9 Figure 6: Installing memory card ................ 11 Figure 7: Keypad layout ..................
  • Page 12 Contents: Sample Screens Screen 1: Status lights as menu indicators ............39 Screen 2: System Menu> 1. Information ............43 Screen 3: System Menu> 2. Settings ..............44 Screen 4: System Menu> 2. Settings> 1. Clock ..........44 Screen 5: System Menu> 2. Settings> 2. Backlight Period ........ 45 Screen 6: System Menu>...

  • Page 13: Revision History

    EVISION ISTORY Version Release Date Notes 1.00 Dec. 2004 Initial release 1.01 Jan. 12, 2005 Revised as per the following: 1. Styles updated (Sec. 3.2 & 4.3.6) 2. Font file - downloading interface: RS-232 only (Sec. 5) 3. Update Figure 27 “Remote Management” 1.02 May 16, 2005 Revised as per the following:...
  • Page 14 Reserved. This page is intended to be blank.

  • Page 15: Preface

    Integrated with a proximity reader and backlit keypad, the 5000 terminal simply satisfies general needs regarding large data collection. Based on the 5000 terminal, the 5100 terminal comes with a backlit LCD for displaying information. Alternatively, both models can make use of a battery pack for achieving a non-interruptible operation during power outage.
  • Page 16 Reserved. This page is intended to be blank.

  • Page 17: Care & Maintenance

    & M AINTENANCE This is specifically prepared for those who are in charge of taking care of the terminals, such as a terminal operator or maintenance engineer. Here are some tips on how to take care and maintain the terminals. Taking care of the terminal Always keep electric equipments like the terminals away from any flammable sources.

  • Page 18: Getting Ready

    ETTING EADY If you are using the terminal for the first time, the illustration below gives outline of the system and section references. Access to the configuration menus needs to disconnect the external and internal power connection of the terminal first. Therefore, we suggest that you do all the configuration and downloading jobs before setting up the system on site.

  • Page 19: Introducing 5000/5100

    NTRODUCING This section mainly explains the hardware construction and features of the 5000/5100 terminals. The 5100 terminal looks similar to the 5000 terminal except for the screen. 1.1 Product Highlights 2, 4 or 8 MB for expandable data memory, powered by backup cell...

  • Page 20: Nomenclature

    Introducing 5000/5100: Nomenclature 1.2 Nomenclature The pictures below show the major components: Figure 2: Nomenclature of terminal...

  • Page 21: Inside Enclosures

    Introducing 5000/5100: Nomenclature 1.2.1 Inside Enclosures Figure 3: Components inside terminal...

  • Page 22: Dimensions

    Introducing 5000/5100: Nomenclature 1.2.2 Dimensions These drawings provide 3-sided views with dimensions, which are helpful in choosing a suitable location for installation. Figure 4: Physical dimensions...

  • Page 23: Features

    1.3.1 Power Line Power & Main Battery A 12 V/ 1000 mA wall adaptor is used to power the 5000/5100 terminals. Furthermore, an optional 7.4 V/ 2000 mAh Li-ion battery pack provides more than six extra hours of uninterrupted operations when the line power is down. Such power switching mechanism is actuated by a power switch, which seamlessly switches between the line power and the battery pack without any user’s intervention.

  • Page 24: Table 1: Power Consumption

    Introducing 5000/5100: Features Power Consumption Status The System Menu provides information on power consumption. Monitor voltage level: Line / Main / Backup >> Also see Section 4.3.5 Power For the 5100 terminal, the smart battery icon will replace the plug icon on the screen when it is battery-operated.

  • Page 25: Figure 5: Installing Battery Pack

    Introducing 5000/5100: Features Installing Battery Pack If there is any need to replace the battery pack, follow the instructions described below. 1. Seat the battery pack into the battery compartment at the lower enclosure. 2. Connect the battery wires to the receptacle on the charger.

  • Page 26: Cpu

    Introducing 5000/5100: Features 1.3.2 CPU A 16-bit low power CMOS CPU is utilized. With little current consumed, yet, this CPU can run under 22.1184MHz and provide more than 6 MIPS of computation powers. 1.3.3 Memory & Calendar In the event of a power failure with no battery pack installed, the 7 mAh button cell on the main board is to keep contents of the SRAM and run the calendar for at least 1 week.

  • Page 27: Figure 6: Installing Memory Card

    Introducing 5000/5100: Features Installing Memory Card 1. Align pinholes at the back of the card to the pins on the main PCB. 2. Press down the card flatly. Be careful not to bend or distort any pins. 3. Then apply the screw to screw down to the pole.

  • Page 28: Keyboard

    Introducing 5000/5100: Features 1.3.4 Keyboard A 21-key keypad is for system setup, user entry and so on. Figure 7: Keypad layout Silicon rubber has been chosen for their durability and prompt feedback. The key click can be configured through the System Menu.

  • Page 29: Lcd

    Introducing 5000/5100: Features Optional External Keyboard The 5000/5100 terminals provide one keyboard port. You may connect an external keyboard to this port. 1. Connect wires from the keyboard module to the receptacle on the main PCB. 2. Connect the external keyboard to the PS/2 port.

  • Page 30: Status Leds

    Introducing 5000/5100: Features 1.3.6 Status LEDs There are four indicators on the front panel for status feedback. They are programmable for diagnostics and application dependant. Red LED – Power Green LED – Good Read Yellow LED – 485 Comm. Orange LED –...

  • Page 31: Digital Inputs

    Introducing 5000/5100: Features 1.3.9 Digital Inputs There are totally 4 groups of digital inputs. Each is electrically isolated from the outside world by a photo-coupler. Current must flow through the internal LED to turn on the output transistor. A typical 1 mA turn-on current is recommended.

  • Page 32: Digital Outputs

    Introducing 5000/5100: Features 1.3.10 Digital Outputs There are totally 4 groups of digital outputs. Each is a relay that is able to sustain 1 A under 30 VDC or 0.3 A under 125 VAC. Both normal open (NO) and normal close (NC) contacts are provided to accommodate application needs.

  • Page 33: Rs-232

    Introducing 5000/5100: Features 1.3.11 RS-232 A standard RS-232 port is available on the JP3. Unlike the “external reader port”, these signals are true RS-232C compliant. With proper cabling, shielding, wiring and so on, it is able to communicate to another device up to 50 feet (approx. 15 meters) away.

  • Page 34: Rs-485

    Though it is simple and low cost, care must be taken to ensure proper operations. The data rate is 125 kbps. Compatible to CipherLAB 510, 520 and so on. Maximum network run length is 1000 meters No fork, nor star connections. As depicted below, connections b, d & f are acceptable but not others.

  • Page 35: Figure 11: An Example Of Rs-485 Connection

    Introducing 5000/5100: Features The illustration below shows a typical topology of networking multiple terminals through RS-232 and RS-485 interfaces. Figure 11: An example of RS-485 connection...

  • Page 36: Ethernet

    Introducing 5000/5100: Features 1.3.13 Ethernet An optional 10/100 Base-T Ethernet card can be attached to merge the terminals onto any existing legacy Ethernet networks. It comes with a standard RJ-45 connector and is fully standard compliant. Just like the RS-485, the IP address must be set accordingly.

  • Page 37: Programming Support

    Introducing 5000/5100: Features Installing Ethernet Card You may have to install the Ethernet card to the terminal by yourself. If you have installed a memory card, attach the Ethernet card on top of it then. 1. Align the pinholes at the back of the card to the pins on the main PCB.

  • Page 38: Unpacking The Package

    The following items are included in the package. Save the box and packaging material for future use when you need to store or ship the terminal. The 5000 or 5100 Terminal Power Adaptor Software CD & Reference Manual (for authorized distributors only) 1.5 Options...

  • Page 39: Installing 5000/5100

    2. I 5000/5100 NSTALLING 2.1 Setting up the terminal The whole installation can be simply classified into the following stages: Site Survey: Choose a location that is close to the target door and provides clearance for the cables and access to an AC outlet.

  • Page 40: Figure 14: Drilling Holes & Assembling Cables

    Installing 5000/5100: Setting up the terminal Figure 14: Drilling holes & assembling cables Drilling Holes & Assembling Cables 1. Make use of the mounting template provided in the appendix, and drill four holes in an appropriate location for installing the terminal: Each hole shall be 6 mm in diameter and 21 mm in depth.

  • Page 41: Figure 15: Mounting To Wall

    Installing 5000/5100: Setting up the terminal Figure 15: Mounting to wall Mounting to the Wall 4. Make sure the cables are routing and arranged in the cable channel at the back. Such design is to keep cables invisible and inaccessible from the outside.

  • Page 42: Figure 16: Wiring & Connecting

    Installing 5000/5100: Setting up the terminal Figure 16: Wiring & connecting Wiring & Connecting 7. Attach connectors of the keyboard module, reader module, charger or battery pack to receptacles on the PCB. 8. Follow the wiring instructions to insert every wire to a corresponding slot of the terminal blocks .

  • Page 43: Figure 17: Assembling Enclosures

    Installing 5000/5100: Setting up the terminal Figure 17: Assembling enclosures Assembling Enclosures from Bottom to Top 10. Make sure there is no more need to do hardware configuration and/or downloading application program. At last, position the two tabs at the bottom of the upper enclosure into the notches at the bottom of the lower enclosure.

  • Page 44: Wiring

    Installing 5000/5100: Wiring 2.2 Wiring This section gives instructions on how to wire the terminal to external devices, a host, or another terminal. RS-232 (JP3) Connect to a host computer Connect to another terminal RS-485 (JP3) Connect to external devices like an actuator (button) to...

  • Page 45: Pin Assignments

    Installing 5000/5100: Wiring 2.2.1 Pin Assignments The pin assignments are listed and described below. JP2: Pin No. Name Category Description Power Ground Power Ground CTS0 From External reader CMOS-level clear to send RTS0 To External reader CMOS-level request to send...

  • Page 46: Table 11: Pin Assignment Of Jp3

    Installing 5000/5100: Wiring JP3: Pin No. Name Category Description Power Same as JP2 pin 7, i.e. total current can be drawn from these two pins is 200 mA DIN1+ Digital input #1 positive side (anode) DIN1- Digital input #1 negative side (cathode)

  • Page 47: Rs-232

    Installing 5000/5100: Wiring 2.2.2 RS-232 Without using additional devices like optical isolators or signal boosters, the cable length is limited to 50 feet (approx. 15 meters) to ensure communication quality according to IEEE standard. Instructions Make use of a 9-pin female connector (DB-9) at PC end, and wire pins as follows:...

  • Page 48: Rs-485

    Installing 5000/5100: Wiring 2.2.3 RS-485 Connections between every two terminals are set up through RS-485 interface. When more than two of the terminals are connected (as a multi-station system), a host only needs to connect to the first one terminal (master) and it can then communicate with the rest terminals (slave).

  • Page 49: Figure 21: Rs-485 Wiring

    Installing 5000/5100: Wiring Instructions When settings are completed, you may proceed with physical connection between every two terminals. To set up RS-485 connection, the communications cable must be wired as shown below: Figure 21: RS-485 wiring Wiring materials: Please use 22 AWG braided shielded cable or Cat 5 UTP (Unshielded Twisted Pair)

  • Page 50: Digital Inputs/Outputs

    Installing 5000/5100: Wiring 2.2.4 Digital Inputs/Outputs DI/DO are four sets of separate signal on the terminals. DI via JP3 D/I type: A photo-coupler that can be used to monitor external devices. For example, a button can be used to activate and open a door.

  • Page 51: System Architecture

    3. S YSTEM RCHITECTURE The whole system can be simplified as hardware and software at PC end and terminal end. The software inside the terminal mainly consists of three modules: Kernel, System, and Program. For system configurations and managing multiple programs, each terminal comes with System Menu, Kernel Menu, and Program Manager.

  • Page 52: Operation

    Program Manager A portal to manage multiple programs. Table 14: Purposes of software modules/menus Because the 5000 terminal comes without the LCD screen, we suggest you keep the manual at hand while configuring the terminals. 3.1 Operation After being properly configured and physically set up together with peripherals, the terminal is ready to work when a corresponding management utility is ready at PC end.

  • Page 53: Download

    System Architecture: Download 3.2 Download The terminal must be configured correctly for downloading either of the following: Program update New application program Font file (only RS-232 interface is allowed) Proprietary Application Programs (5100*.SHX): The following programs have been developed to meet varying application needs. One of them is preloaded inside the terminal.

  • Page 54: Management

    System Architecture: Management 3.3 Management Install a management utility at PC end that corresponds to the current application. Then, proceed to define the environments for the terminal to work. Please see programming guide for details. The terminal must be loaded with an appropriate application first. Proprietary Management Software for 5100*.SHX: The software is in correspondence to proprietary application programs.

  • Page 55: Configuring 5000/5100

    This section mainly describes the alternatives to configure the 5000/5100 terminals, including hardware configuration and downloading application programs. Although the 5000 terminal is not equipped with a screen, you may proceed with configurations by following the LED indicators and relevant sample screens of menus in this manual.

  • Page 56: Selecting From Menus

    Configuring 5000/5100: Selecting from menus 4.2 Selecting from menus The function keys can also be used in selecting item from menus on the screen. To select item 1 to 5 on any menu, simply press [F1] to [F5]. To select item 6 on any menu, press [F6] then [F1].

  • Page 57: Figure 23: Function Keys As Menu Indicators

    Configuring 5000/5100: Selecting from menus Figure 23: Function keys as menu indicators...

  • Page 58: System Menu

    Configuring 5000/5100: System Menu 4.3 System Menu The System Menu is generated by a powerful utility, which offers an interface for engineers (programmers or system integrator) to view system information, change the configuration parameters, manage files and run diagnostics. This menu is designed for engineering tests and maintenance ONLY. For this reason, the System Menu provides password protection to prevent unauthorized users from accidentally changing system settings.

  • Page 59: Information

    C library version USR: Application program version DEV: Code for optional hardware configurations, i.e. 1700. See Kernel> Information for device code. NET: Serial number of Ethernet card if installed Without a screen, this is not available on the 5000 terminals.

  • Page 60: Settings

    Configuring 5000/5100: System Menu 4.3.2 Settings Screen 3: System Menu> 2. Settings Here provides options to change the default settings. System settings Default values Clock Backlight Period 20 seconds CPU Speed Full speed Key Click Tone 2 System Password Open access...
  • Page 61 Configuring 5000/5100: System Menu Settings > Backlight Period Set the backlight duration for the keypad and LCD. Enter a value between 0 and 99999. Screen 5: System Menu> 2. Settings> 2. Backlight Period Settings > CPU Speed Set the CPU speed to save power if necessary. The current value is highlighted.
  • Page 62 Configuring 5000/5100: System Menu Settings > Key Click There is audible feedback for pressing a key on the keypad. The current value is highlighted. Select a tone for the buzzer or mute it. Screen 7: System Menu> 2. Settings> 4. Key Click Settings >...
  • Page 63 The font settings here can be changed if a multi-languages font file has been downloaded. (Press [2] / [8] to move down / up the menu of options.) Screen 9: System Menu> 2. Settings> 6. Font Without a screen, this is not available on the 5000 terminals.

  • Page 64: Tests

    Test the data memory (SRAM), and the results will be shown on the screen. Press any key to exit. Without a screen, this is not available on the 5000 terminals. Warning! The contents of the data memory (SRAM) will be wiped out after test.
  • Page 65 Test the LCD display and LED indicator. Press [Enter] to start. Press any key to stop and exit the test. You may only be able to test the LED indicators on the 5000 terminals. Tests > Keyboard Test the rubber keys.

  • Page 66: Memory

    (SRAM for data memory) Flash (for program memory) Without a screen, this is not available on the 5000 terminals. Memory > Initialize Perform task initializing the data memory (Base RAM or Memory Card). Warning! The contents of the data memory (SRAM) will be wiped out after memory...

  • Page 67: Power

    The battery pack is a standby power source when line power is down. Backup: Backup battery status. The button cell is used to retain data in SRAM and maintain RTC. Without a screen, this is not available on the 5000 terminals.

  • Page 68: Load Program

    Configuring 5000/5100: System Menu 4.3.6 Load Program Screen 13: System Menu> 6. Load Program The terminal must be configured correctly for downloading either of the following: Program update New application program Font file (only RS-232 interface is allowed) RS-232 Default parameters are 115200, none, 8, 1.

  • Page 69: Net Menu

    MAC ID of the installed Ethernet (TCP/IP) module DHCP: DHCP being enabled or disabled IP address of the terminal Mask: Subnet Mask Gate: Default Gateway Screen 15: System Menu> 7. Net Menu> 1. Information Without a screen, this is not available on the 5000 terminals.
  • Page 70 Configuring 5000/5100: System Menu Net Menu > IP Setting Set network parameters: DHCP: Options – Enable or Disable SubNet Mask: Enter a new Mask IP, if necessary. Local IP Address: Enter a new address for the terminal, if necessary. Default Gateway: Enter a new address for the default Gateway, if necessary.
  • Page 71 Configuring 5000/5100: System Menu Screen 16: System Menu> 7. Net Menu> 2. IP Setting...
  • Page 72 Configuring 5000/5100: System Menu Net Menu > Echo Tests Echo tests are used for verify connectivity. Press [ESC] to stop and exit the test. You also need a test utility on PC to test the networking. Screen 17: System Menu> 7. Net Menu> 3. Echo Tests...
  • Page 73 Configuring 5000/5100: System Menu Client Mode: Set the terminal as a client. Enter the IP address of a server that connection is desired. Followed by an attempt to make connection with the access point. Server Mode: Set the terminal as a server.
  • Page 74 Configuring 5000/5100: System Menu Net Menu > Download via TCP/IP If an Ethernet card is installed, the terminal can download new application program or program update via TCP/IP. You also need a downloading utility on PC to download program through network.

  • Page 75: Program Manager

    Configuring 5000/5100: Program Manager 4.4 Program Manager The 5000/5100 terminals support multiple applications and languages. In the menu of Program Manager, it can download up to seven programs and one of them is made active. Warning! The Program Manager menu is NOT for the use of any end users.

  • Page 76: Download

    Configuring 5000/5100: Program Manager 4.4.1 Download Screen 20: Program Manager> 1. Download Multiple programs as well as custom font file can be downloaded through RS-232 interface. There is a full list of programs and font file that are currently stored in the terminal as follows.

  • Page 77: Table 21: Downloading Spare Programs

    Configuring 5000/5100: Program Manager Spare application programs Empty slot: 1. Select an empty slot by pressing the corresponding number and then [Enter]. 2. Select baud rate for downloading. Set matching parameters at PC end. 3. Connect cable and wait connecting…...

  • Page 78: Table 22: Downloading Active Program Or Font

    Configuring 5000/5100: Program Manager Active application program or font file The active slot: 1. Select the active program (may be an empty slot) by pressing the corresponding number (that is 7) and then [Enter]. 2. Set matching parameters at PC end: 115200, none, 8, 1 3.

  • Page 79: Activate

    Configuring 5000/5100: Program Manager 4.4.2 Activate Screen 21: Program Manager> 2. Activate The list shows the entire spare programs stored in the terminal. From the list, you can select from 01 to 06 and activate one of them. When an application program is activated, it will be copied to the active memory and replace the old one.

  • Page 80: Version

    Configuring 5000/5100: Program Manager 4.4.3 Version Here provides information about the version of Program Manager. Without a screen, this is not available on the 5000 terminals.

  • Page 81: Kernel Menu

    Configuring 5000/5100: Kernel Menu 4.5 Kernel Menu The Kernel Menu resides in the innermost core of the system. It has the highest security and is always protected by the system. When the application program is corrupted and the System Menu fails, the Kernel Menu provides an access to fix the system.

  • Page 82: Information

    Code for optional hardware configurations, i.e. 1700 Type of Reader Module Type of LAN Module Reserved Reserved 0= none 0= none 1= EM 7= Ethernet 2= Mifare Table 23: Device code explained Without a screen, this is not available on the 5000 terminals.

  • Page 83: Load Program

    Configuring 5000/5100: Kernel Menu 4.5.2 Load Program The terminal must be configured correctly for downloading either of the following: Program update New application program Font file 1. Connect RS-232 cable. 2. Set communication parameters at PC end: 115200, none, 8, 1.

  • Page 84: Kernel Update

    Configuring 5000/5100: Kernel Menu 4.5.3 Kernel Update The Kernel might be changed for improving performance or other reasons, and an update is necessary. 1. Connect cable. 2. Set communication parameters at PC end: 115200, none, 8, 1. 3. Enter Kernel Menu> Kernel Update.

  • Page 85: Managing 5000/5100

    5. M 5000/5100 ANAGING Depending on the application program downloaded to the terminals, managing the 5000/5100 terminals at PC end can be very flexible and simple. For details, please see relevant documents such as Programming Guide. Figure 27: Remote management...

  • Page 86: For Proprietary Applications

    Managing 5000/5100 5.1 For proprietary applications For any preloaded application program (5100*.SHX), we provide several ways for managing the terminal from PC end. Management Utilities This is application dependant. For example, Menjin.exe is developed for Access Control application. Commands Sending commands serves as an alternative to manage the terminals.

  • Page 87: Specifications

    PECIFICATIONS Power 12 V ± 5% DC at 1000 mA Line power: Main battery: Rechargeable 7.4 V, 2000 mAh Li-ion battery pack (optional) Backup battery: Rechargeable 3.0 V, 7 mAh Lithium button cell 16-bit CPU: Tunable clock, up to 22 MHz Memory Flash: 2 MB program memory...
  • Page 88 Specifications Enclosure Material & Color: ABS plastic Black Dimensions: 150 mm (L) x 150 mm (W) x 50 mm (H) Weight: Approx. 1.6 Kg (including one battery pack) Input Devices Reader: Built-in RFID reader, Mifare or EM type (optional) Also allow for one external TTL RS-232 reader Keyboard: 21 keys rubber including 6 function keys, backlit, programmable One external Mini Din connector provided by keyboard module...

  • Page 89: Troubleshooting

    ROUBLESHOOTING The terminal cannot accept valid cards… Regarding power – Check if the power adaptor is plugged into a wall outlet. Check if the outlet is working. If the problem persists, check if the wiring inside the terminal is correct and secured. Regarding memory –...
  • Page 90 Troubleshooting The keyboard input seems not working properly… Test keyboard. >> Also see Section 4.3.3 Tests: Keyboard If the problem persists, re-connect the power and perform test. The external devices controlled by DI/DO signals are not working properly… Check if the device is properly wired to the terminal blocks. If the problem persists, re-connect the power and perform test.

  • Page 91: Appendixi - Mounting Template

    I – M PPENDIX OUNTING EMPLATE This mounting template is provided in actual size (1:1 scale). 1. Place this paper on the place you desire to mount the terminal. 2. Use paper tape to attach it on the surface. 3. Then use a power drill to drill holes on the four corners. The size of these holes is 6mm in diameter and 21mm in depth.

This manual is also suitable for:

5100

Table of Contents