Beretta EXCLUSIVE C Installer And User Manual page 21

RANGE RATED
5100
- once the desired power is set (maximum heating) note the value onto the
supplied self-adhesive label. For further checks and adjustments refer to
the set value.
b
The calibration does not cause the boiler ignition.
The boiler is supplied with the settings indicated in the multigas table.
It is nevertheless possible, according to the system requirements or the
regional regulations on the combustion gas emission limits, to set that value
by referring to the graphs below.
EXCLUSIVE 25C n
Curva portata termica - giri ventilatore
Caldaia Vision+ 24C PLUS
HTG curve (Qnheating)
8400
8000
7600
7200
6800
6400
6000
5600
5200
4800
4400
4000
3600
3200
2800
2400
2000
1600
1200
800
2 4 6 8 10
Heat output (kW)
Curva portata termica - emissioni CO
Caldaia Vision+ 24C PLUS
CO s.a. curve (Qnheating)
240
230
220
210
200
190
180
170
160
150
140
130
120
110
100
90
80
70
60
50
40
30
20
10
0
2 4 6 8 10
RPM
12 14 16 18 20 22 24 26
Portata termica (kW)
12 14 16 18 20 22 24 26
Portata termica (kW)
Heat output (kW)
8400
8000
7600
7200
6800
6400
6000
5600
5200
4800
4400
4000
3600
3200
2800
2400
2000
1600
1200
800
2 4
160
150
140
130
120
110
100
90
80
70
60
50
40
30
20
10
0
0 2
5.15 Lights and faults
If any faults should occur, a screen will appear on the display indicating
the relative error code and a brief alphanumeric description of the same.
Pressing the "back/cancel" button it is possible to return to the main
28 30
screen, where a fault is signalled by this flashing icon
The user can return to the fault description screen by using the "up" and
"down" keys and then pressing the "ok" key.
28 30
The faults description screen is automatically displayed once the display
illumination time has elapsed without any button being pressed.
Press the "up" and "down" keys to display the descriptions of any other
faults that may be present.
Reset function
In order to reset the boiler's operation in the event of a fault, it is necessary
to access the fault description screen. If the lockout is of a non-volatile type
that requires a reset procedure, this will be indicated on the screen, and
can be performed by pressing the "ok" button on the REC10.
At this point, if the correct operating conditions have been restored, the
boiler will restart automatically.
There are a maximum of 5 consecutive attempts at a release by the
REC10, when used up it is possible to unlock the boiler by cutting off and
reconnecting the electrical supply.
EXCLUSIVE 30C n
Curva portata termica - giri ventilatore
Caldaia Vision+ 28C PLUS
HTG curve (Qnheating)
6 8 10 12 14 16 18
Portata termica (kW)
Heat output (kW)
Curva portata termica - emissioni CO
Caldaia Vision+ 28C PLUS
CO s.a. curve (Qnheating)
4 6 8 10 12 14 16 18 20
Portata termica (kW)
Heat output (kW)
FRI
PLANT
18/05/2013
1.3 bar
MENU
42
°C
INFO SET
HOT WATER TEMPERATURE
E020
LIMIT THERMOSTAT
REC10 ATTEMPTS EXHAUSTED
ENGLISH
20 22 24 26 28 30
22 24 26 28 30 32
.
12:17
STATE
21