Parameter Group B - Omron 3G3RX Quick Start Manual

RX Quick Start Guide
Function code Function name
A105 OI start selection
A111 O2 start frequency
A112 O2 end frequency
A113 O2 start ratio
A114 O2 end ratio
A131 Acceleration curve parameter
A132 Deceleration curve parameter
A141 Operation frequency input A setting
A142 Operation frequency input B setting
A143 Operator selection
A145 Frequency addition amount
A146 Frequency addition direction
A150 EL-S-curve ratio 1 during acceleration
A151 EL-S-curve ratio 2 during acceleration
A152 EL-S-curve ratio 1 during deceleration
A153 EL-S-curve ratio 2 during deceleration

4.3 Parameter group B

Function code Function name
b001 Retry selection
b002 Allowable momentary power interruption time
b003 Retry wait time
b004 Momentary power interruption/undervoltage trip
during stop selection
b005 Momentary power interruption retry time selection
b006 Input phase loss protection selection
b007 Frequency matching lower limit frequency setting
b008 Trip retry selection
b009 Undervoltage retry time selection
b010 Overvoltage/overcurrent retry time selection
b011 Trip retry wait time
b012 Electronic thermal level
b212 2nd electronic thermal level
b312 3rd electronic thermal level
b013 Electronic thermal characteristics selection
40
Monitoring and setting items
00: Start FQ (Use OI start frequency [A101])
01: 0 Hz
-400.00 to 400.00
-400.00 to 400.00
-100 to O2 end ratio
O2 start ratio to 100
01 (small curve) to 10 (large curve)
01 (small curve) to 10 (large curve)
00: Operator (Digital operator (F001))
01: VR (Digital operator (FREQ adjuster)) (Enabled
when 3G3AX-OP01 is used)
02: O (Input O)
03: OI (Input OI)
04: Modbus (RS485 communication)
05: Option 1
06: Option 2
07: Pulse (Pulse train frequency)
00: Operator (Digital operator (F001))
01: VR (Digital operator (FREQ adjuster)) (Enabled
when 3G3AX-OP01 is used)
02: O (Input O)
03: OI (Input OI)
04: Modbus (RS485 communication)
05: Option 1
06: Option 2
07: Pulse (Pulse train frequency)
00: ADD (Addition (A + B))
01: SUB (Substraction (A - B))
03: MUL (Multiplication (A x B))
0.00 to 400.00
00: ADD (Add A145 value to output frequency)
01: SUB (Subtract A145 value from output frequency)
0 to 50
0 to 50
0 to 50
0 to 50
Monitoring and setting items
00: TRIP (Alarm)
01: 0 Hz start
02: f-match (Frequency matching start)
03: f-match trip (Trip after frequency matching decelera-
tion stop)
04: Actv. f-match (Active frequency matching restart)
0.3 to 25.0
0.3 to 100.0
00: OFF (Disabled)
01: ON (Enabled)
02: Decel-OFF (Disabled during stop and deceleration
stop)
00: 16 times
01: No limit
00: OFF (Disabled)
01: ON (Enabled)
0.00 to 400.00
00: TRIP (Alarm)
01: 0 Hz start
02: f-match (Frequency matching start)
03: f-match trip (Trip after frequency matching decelera-
tion stop)
04: Actv. f-match (Active frequency matching restart)
00: 16 times
01: No limit
1 to 3
0.3 to 100.0
0.20 x Rated current to 1.00 x Rated current
0.20 x Rated current to 1.00 x Rated current
0.20 x Rated current to 1.00 x Rated current
00: Reduced TRQ (Reduced torque characteristics)
01: Const TRQ (Constant torque characteristics)
02: Free set (Free setting)
Units Run Modbus Default
mode Register
edit Nº

– 1287h 00

Hz 128Dh 0.00
128Eh

Hz 128Fh 0.00
1290h

% 1291h -100

% 1292h 100

– 12A5h 02

- 12A6h 02

- 12AFh 02

– 12B0h 03

– 12B1h 00

Hz 12B3h 0.00
12B4h

– 12B5h 00

% 12B9h 10

% 12BAh 10

% 12BBh 10

% 12BCh 10
Units Run Modbus Default
mode Register
edit No.

– 1301h

s 1302h 1.0

s 1303h 1.0

– 1304h

– 1305h

– 1306h

Hz 1307h 0.00
1308h

– 1309h

– 130Ah

Time 130Bh

s 130Ch 1.0

A 130Dh

A 230Ch

A 330Ch

– 130Eh
RX Quick Start Guide
00
00
00
00
00
00
3
-
-
-
00