MTU 16V4000M73 Operating Instructions Manual page 4

8.5.1 Valve protrusion - Measurement
8.5.2 Valve gear - Lubrication
8.5.3 Valve clearance - Check and adjustment
8.5.4 Cylinder head cover - Removal and
installation
8.6 Injection Pump / HP Pump
8.6.1 HP fuel pump - Filling with engine oil
8.7 Injector
8.7.1 Injector - Replacement
8.7.2 Injector - Removal and installation (jacketed
fuel system)
8.8 Fuel Filter
8.8.1 Fuel filter - Replacement
8.8.2 Fuel prefilter - Contamination indicator check
8.8.3 Fuel prefilter - Draining
8.8.4 Fuel prefilter - Flushing
8.8.5 Fuel prefilter with water separator - Filter
element replacement
8.9 Exhaust Turbocharger
8.9.1 Compressor wheel - Cleaning
8.10 Charge-Air Cooling
8.10.1 Intercooler - Check water drain for coolant
leakage and obstruction
8.11 Air Filter
8.11.1 Air filter - Replacement
8.11.2 Air filter - Removal and installation
8.12 Air Intake
8.12.1 Service indicator - Signal ring position check
8.13 Exhaust Gas Aftertreatment
8.13.1 Supply unit - Filter element replacement
8.13.2 Supply unit - Replacement
8.13.3 Dosing unit - Replacement
8.13.4 Urea solution lines - Replacement
8.13.5 Insulation of SCR housing and SCR bypass -
Check
8.13.6 Pre-feed module - Filter element replacement
8.13.7 Pre-feed module - Replacement
8.13.8 Exhaust pressure sensor - Measuring lines
check
8.13.9 Exhaust pressure sensor - Measuring lines
cleaning
8.13.10 SCR catalytic converter - Mounting alignment
8.13.11 SCR catalytic converter - Mounting check
8.13.12 SCR modules - Replacement
8.13.13 NOx sensor - Replacement
8.14 Starting Equipment
8.14.1 Starter - Condition check
8.15 Lube Oil System, Lube Oil Circuit
8.15.1 Engine oil level - Check
8.15.2 Engine oil - Change
8.15.3 Engine oil - Sample extraction and analysis
4 | Table of Contents | MS150123/01E 2017-05
8.16 Oil Filtration / Cooling
136
140
8.16.1 Automatic oil filter - Overview
141
8.16.2 Automatic oil filter - Preparatory steps
8.16.3 Automatic oil filter - Removal
145
8.16.4 Automatic oil filter - Disassembly
8.16.5 Automatic oil filter - Cleaning
146
8.16.6 Automatic oil filter - Checking flushing arm
146
rotation
148
8.16.7 Automatic oil filter - Check
8.16.8 Automatic oil filter - Assembly
148
8.16.9 Automatic oil filter - Installation
8.16.10 Automatic oil filter - Final steps
149
8.16.11 Oil filter element - Overview
155
8.16.12 Oil filter element - Removal
155
8.16.13 Oil filter element - Disassembly
157
8.16.14 Oil filter element - Cleaning
159
8.16.15 Oil filter element - Check
161
8.16.16 Oil filter element - Assembly
8.16.17 Oil filter element - Installation
163
8.16.18 Oil indicator filter - Cleaning and check
8.16.19 Centrifugal oil filter - Overview
166
8.16.20 Centrifugal oil filter - Cleaning and filter-
166
sleeve replacement
170
8.16.21 Centrifugal oil filter - Removal and
installation
170
8.17 Coolant System, General, High-Temperature
171
Circuit
171
8.17.1 Engine coolant - Level check
172
8.17.2 Engine coolant - Change
8.17.3 Engine coolant - Draining
173
8.17.4 Engine coolant - Filling
173
8.17.5 Engine coolant pump - Relief bore check
174
8.17.6 Engine coolant - Sample extraction and
174
analysis
177
8.17.7 Preheater - Overview
180
8.17.8 Preheater - Removal
183
8.17.9 Preheater - Overhaul
8.17.10 Preheater - Installation
184
8.17.11 Preheater - Function and leak-tightness check
185
8.17.12 Heating element(s) - Electrical check
187
8.17.13 Valve cover - Replacement
8.18 Raw Water Pump with Connections
189
8.18.1 Raw water pump - Relief bore check
190
8.19 Battery-Charging Generator
191
8.19.1 Battery-charging generator drive - Coupling
193
condition check
194
8.20 Engine Mounting / Support
199
8.20.1 Engine mounting - Check
202
8.20.2 Engine mounting - Checking securing screws
202
for firm seating
203
8.21 Auxiliary PTO
203
8.21.1 Bilge pump - Relief bore check
204
8.22 Fuel Supply System
206
8.22.1 Water drain valve - Check
207
207
210
211
213
214
215
216
217
218
220
221
223
224
226
227
228
232
235
238
239
241
242
242
243
244
245
248
249
250
251
252
253
254
255
256
257
257
258
258
259
259
260
261
261
262
262