Danfoss VLT AQUA FC 202 Operating Instructions Manual page 53

Specifications
Type designation
1)
High/normal overload
Typical shaft output [kW]
Typical shaft output at 460 V [hp]
6)
IP20/Chassis
IP21/Type 1
IP55/Type 12
IP66/NEMA 4X
Output current
Continuous (3x380-440 V) [A]
Intermittent (60 s overload)
(3x380-440 V) [A]
Continuous (3x441-480 V) [A]
Intermittent (60 s overload)
(3x441-480 V) [A]
Continuous kVA at 400 V [kVA]
Continuous kVA at 460 V [kVA]
Maximum input current
Continuous (3x380-440 V) [A]
Intermittent (60 s overload)
(3x380-440 V) [A]
Continuous (3x441-480 V) [A]
Intermittent (60 s overload)
(3x441-480 V) [A]
Maximum pre-fuses [A]
Additional specifications
IP21, IP55, IP66 maximum cable
cross-section 2) for mains, brake,
and load sharing [mm 2 ] ([AWG])
IP21, IP55, IP66 maximum cable
2) 2
cross-section for motor [mm ]
([AWG])
IP20 maximum cable cross-
section 2) for mains, brake, motor,
2
and load sharing [mm ] ([AWG])
2)
Maximum cable cross-section for
2
disconnect [mm ] ([AWG])
Estimated power loss 3)
at rated maximum load [W]
4)
Efficiency
Table 8.9 Mains Supply 3x380-480 V AC, P11K-P30K
MG20MB02
Operating Instructions
P11K P15K
HO NO HO NO
7.5 11 11 15
10 15 15 20
B3 B3
B1 B1
B1 B1
- 24 24 32
- 26.4 38.4 35.2
- 21 21 27
- 23.1 33.6 29.7
- 16.6 16.6 22.2
- 16.7 16.7 21.5
- 22 22 29
- 24.2 35.2 31.9
- 19 19 25
- 20.9 30.4 27.5
- 63 63
16, 10, 16 (6, 8, 6)
10, 10,- (8, 8,-)
10, 10,- (8, 8,-)
291 392 291 392
0.98 0.98
Danfoss A/S © Rev. 05/2014 All rights reserved.
P18K P22K
HO NO HO
15 18.5 22.0
20 25 30
B3 B4
B1 B2
B1 B2
32 37.5 37.5
51.2 41.3 60
27 34 34
43.2 37.4 54.4
22.2 26 26
21.5 27.1 27.1
29 34 34
46.4 37.4 54.4
25 31 31
40 34.1 49.6
63
35, 25, 25 (2, 4, 4)
16, 10, 10 (6, 8, 8)
379 465 444
0.98 0.98
P30K
NO HO NO
22.0 22.0 30
30 30 40
B4
B2
B2
44 44 61
48.4 70.4 67.1
40 40 52
44 64 61.6
30.5 30.5 42.3
31.9 31.9 41.4
40 40 55
44 64 60.5
36 36 47
39.6 57.6 51.7
63 80
35, -, - (2, -, -)
35, -, - (2, -, -)
525 547 739
0.98
51
8 8