Emerson Oxymitter 5000 Instruction Manual page 7

Oxymitter 5000
Figure 1. Oxymitter 5000 Installation Options..................................................................... P-12
Figure 2. Oxymitter 5000 with SPS 4000 Wiring Diagram.................................................. P-15
Figure 3. Oxymitter 5000 without SPS 4000 Wiring Diagram............................................. P-15
Figure 1-1. Typical System Package ....................................................................................... 1-0
Figure 1-2. Oxymitter 5000 Autocalibration System Options ................................................... 1-3
Figure 1-3. Oxymitter 5000 FOUNDATION Fieldbus Connections.......................................... 1-4
Figure 1-4. Typical System Installation .................................................................................... 1-5
Figure 1-5. SPS 4000............................................................................................................... 1-6
Figure 2-1. Oxymitter 5000 Installation .................................................................................... 2-2
Figure 2-2. Oxymitter 5000 Installation (with SPS 4000) ......................................................... 2-3
Figure 2-3. Oxymitter 5000 with Abrasive Shield ..................................................................... 2-4
Figure 2-4. Oxymitter 5000 Adaptor Plate Installation ............................................................. 2-5
Figure 2-5. Oxymitter 5000 Mounting Flange Installation ........................................................ 2-6
Figure 2-6. Oxymitter 5000 Bracing Installation ....................................................................... 2-7
Figure 2-7. Orienting the Optional Vee Deflector ..................................................................... 2-7
Figure 2-8. Installation with Drip Loop and Insulation Removal............................................... 2-8
Figure 2-9. Terminal Block ..................................................................................................... 2-10
Figure 2-10. SPS 4000 Electrical Connections ........................................................................ 2-12
Figure 2-11. Air Set, Plant Air Connection ............................................................................... 2-13
Figure 2-12. Oxymitter 5000 Gas Connections........................................................................ 2-14
Figure 3-1. Integral Electronics ................................................................................................ 3-1
Figure 3-2. Oxymitter 5000 Defaults ........................................................................................ 3-3
Figure 3-3. Startup and Normal Operation............................................................................... 3-6
Figure 3-4. Calibration Keys..................................................................................................... 3-7
Figure 3-5. Normal Operation................................................................................................... 3-8
Figure 4-1. Oxymitter 5000 Exploded View.............................................................................. 4-2
Figure 4-2. Membrane Keypad................................................................................................. 4-3
Figure 4-3. Inside Right Cover ................................................................................................. 4-4
Figure 4-4. Terminal Block ....................................................................................................... 4-7
Figure 4-5. Electronic Assembly............................................................................................... 4-8
Figure 4-6. J8 Connector.......................................................................................................... 4-9
Figure 4-7. Fuse Location ...................................................................................................... 4-11
Figure 4-8. Heater Strut Assembly......................................................................................... 4-13
Figure 4-9. Cell Replacement Kit ........................................................................................... 4-14
Figure 4-10. Ceramic Diffusion Element Replacement............................................................ 4-16
Figure 4-11. SPS 4000 Manifold Assembly ............................................................................. 4-18
Figure 4-12. Power Supply Board and Interface Board Connections ...................................... 4-20
Figure 4-13. Calibration Gas and Reference Air Components ................................................ 4-24
Figure 5-1. Fault 1, Open Thermocouple ................................................................................. 5-3
Figure 5-2. Fault 2, Shorted Thermocouple ............................................................................. 5-4
Figure 5-3. Fault 3, Reversed Thermocouple .......................................................................... 5-5
Figure 5-4. Fault 4, A/D Comm Error ....................................................................................... 5-6
Figure 5-5. Fault 5, Open Heater ............................................................................................. 5-7
Figure 5-6. Fault 6, High High Heater Temp ............................................................................ 5-8
Figure 5-7. Fault 7, High Case Temp....................................................................................... 5-9
Figure 5-8. Fault 8, Low Heater Temp ................................................................................... 5-10
Figure 5-9. Fault 9, High Heater Temp .................................................................................. 5-11
Figure 5-10. Fault 10, High Cell mV......................................................................................... 5-12
Figure 5-11. Fault 11, Bad Cell ................................................................................................ 5-13
Figure 5-12. Fault 12, EEPROM Corrupt ................................................................................. 5-14
Rosemount Analytical Inc. A Division of Emerson Process Management
LIST OF ILLUSTRATIONS
Instruction Manual
IB-106-350 Rev. 1.2
April 2001
iii