Summary of Contents for Nilfisk-Advance City Ranger 2250
Page 1
´ peratOr s manual BASIC MACHINE City Ranger 2250 All Year Operation Cost Saving...
Page 2
We ask you to pay particular attention to section 1.1 Safety. The machine must only be serviced by professionals. The City Ranger 2250 is designed only for use by professionals. On delivery, the user will receive thorough training to become a competent operator.
Introduction The utility machine City Ranger 2250 The City Ranger 2250 is an outdoor utility machine with a complete range of special attachments that allows you to work outdoors, all year round. Sweeping and vacuuming in spring and autumn, mowing grass and lawn-edge cutting in the summer, sweeping snow, and spreading gravel and sand in the winter.
(Picture 1) Turn the steering wheel carefully The City Ranger 2250 is articulated – it turns sharply, immediately. (Picture 2) Do not inhale exhaust gas Hinged joint Engine vehicle exhaust gas is hazardous to health and can even be fatal.
Page 6
Do not touch the exhaust pipe as it becomes very hot when the machine is running. (Picture 2) Hydraulic components Be aware that the hydraulic components may get hot when the machine is in use. Exhaust pipe Operator’s Manual City Ranger 2250...
There is an operator’s manual for each attachment. Operation with these attachments must follow the instructions outlined in the relevant operator’s manual. Do not operate the City Ranger 2250 with the attachment unless all instructions have been followed. Operator’s Manual City Ranger 2250...
City Ranger 2250 UHM 2250B0 XX (manufacturing year) Type: A XXXXX (serial number) · has been manufactured in conformity with the provisions of Directive 2003/37/EU Place: Lemvig Date: Signature: Knud Olsen, Senior Engineer Operator’s Manual City Ranger 2250...
Height including roll bar 2,000 mm Max. speed 20 km/h Weight Machine weight (including cab) 970 kg Unladen weight - City Ranger 2250 with roll bar 910 kg Max. permitted weight: Utility machine 1,610 kg Machine and trailer without brakes 2,050 kg...
Page 10
78 dB(A) -in accordance with European Directive 2009/76/EC - Operator seat, open windows 83 dB(A) - Operator seat, closed windows 81 dB(A) Vibration test Whole body, EN 13059 0.7 m/s2 Hand/arm, EN 13059 1.0 m/s2 Operator’s Manual City Ranger 2250...
Page 11
Cab classification according EN 15695-1 is Category 1. This cab category does not provide protection against hazardous substances. City Ranger 2250 fitted with this cab shall not be used under conditions requiring protection against hazardous substances. Turning radius Turning circle inside/outside...
(Picture 3) There is a similar door on the right side. This door is operated in the same way as the left door and can be used as an emergency exit. Cab floor Internal door handle Operator’s Manual City Ranger 2250...
3. Instrument panel. Automatic alarm Turning the ignition key activates the alarm for three seconds, to show that the alarm is working. The alarm sound is repetitive (three seconds –beep ; thirty seconds - pause etc.). Operator’s Manual City Ranger 2250...
Page 14
4. The pre-heater light is activated when the ignition key is turned, showing that the engine pre-heater is on. When the light goes out, the ignition key can be turned all the way to start the City Ranger 2250. 5. Handbrake indicator. 6. Charging light.
Page 15
The handbrake is engaged by: Press the brake pedal all the way down. Lift the handle up. Release the brake pedal again. To disengage the handbrake: Press the brake pedal. This frees the handle. 23. Indicator-light, trailer. Operator’s Manual City Ranger 2250...
In position 2, the LED blitz front (option) turns on together with the beacon. Attention! The LED blitz must not be on during transport on public roads. Check the local regulations for use of LED blitz in working situations. Operator’s Manual City Ranger 2250...
4. Front PTO ON/OFF. turning on the attachment (4) and/or (6). 5. Function (F1), (attachment specific). C) Release the switch after five seconds. 6. Rear PTO ON/OFF. 9. 12 V connector. 7. Function. (F2), (attachment specific). Operator’s Manual City Ranger 2250...
Page 18
11. Function-change switch for front attachment (attachment dependant). 12. Weight distribution ON/OFF switch. 13. Joystick for the rear attachment and hydraulics on the back end. The functions are attachment-dependant. See the attachment operator’s manual. 14. Adjusting weight distribution. 15. Safety cover. Operator’s Manual City Ranger 2250...
Advice when driving on a steep slope Users of City Ranger 2250 have reported that, from time to time, they feel that the machine does not accelerate properly when driving up an incline. The machine is designed to drive on an incline of no more than 22%. However, from experience we know that, under certain conditions, this machine can in fact cope with a steeper incline.
Start /stop function - behind the left rear cover Move the on/off switch to ’ON’ to activate it before starting spreading. (Picture 2) Remember to deactivate the on/off switch when changing the salt and sand spreader to another attachment. Start/stop ON Operator’s Manual City Ranger 2250...
Ass 17 A 16 Diode Indication light, horn and steering column. Spare 1 A 17 3 Amp Glow plug and display. Spare 2 Spare 1 Spare fuse. Spare 2 Spare fuse. Fuses Fuses – Roof Operator’s Manual City Ranger 2250...
Page 22
Main fuse - blue Fuse for signal lights - yellow (Fuse placed before main switch). Main switch City Ranger 2250 will not start unless the main switch under the right rear cover is ON (vertical). (Pictures 2 + 3) Main switch – ON Main switch –...
General information 1.12 Towing Towing When towing City Ranger 2250, attach the tow line to the pull hook on the left side of the machine. (Picture 1) Towing valve The towing valve under the machine is used to move the machine manually.
The couplings and the area around the couplings must be kept clean to avoid an accumulation of dirt (See section 3.1). Attaching an attachment: see the attachment operator’s manual. Operator’s Manual City Ranger 2250...
(Picture 1) Suspension Higher: Adjust by gradually pressing the handle 1. The suspension becomes firmer. Lower: Adjust by gradually releasing the handle 1. The suspension becomes softer. Forwards/backwards: Adjust using the handle 2. (Picture 2) Operator’s Manual City Ranger 2250...
Failure to do so increases the risk of corrosion and bacterial accumulation in the system which can cause discomfort/sickness for the driver. Cabin filter must be checked/cleaned once a year. Operator’s Manual City Ranger 2250...
1. Press the screen release button. (Picture 1) 2. Open the screen. Removing the side screen Release button The side screen can be unhooked, for easier machine servicing. (Pictures 2 and 3) Removing the side screen catch Removing side cover Operator’s Manual City Ranger 2250...
1.20 Opening the loading frame The loading frame can be opened during general service. 1. Pull the release handle back. (Picture 1) 2. Pull the loading frame back all the way (until it cannot move further). Release handle Operator’s Manual City Ranger 2250...
(Picture 3) 6. Tip the cabin/roll bar forwards and chock in place so that the sealing strip can be removed. (Picture 4) Loosen the 2 bolts on each side Bolts under base plate Chock, remove strip Operator’s Manual City Ranger 2250...
Page 30
10. Remove the two bolts under the base plate at the front Pull out the cables of the machine. (Picture 2) 11. Lift off the cab/roll bar (min. 2 people). (Picture 3) Bolts under base plate Lift off cab/roll bar Operator’s Manual City Ranger 2250...
Trim off some of the width of the strip adjacent to the holes if necessary. 5. Position spacers. (Picture 4) Bolts under base plate Chock, attach strip Position spacers Operator’s Manual City Ranger 2250...
Page 32
10. Fit the filter and grate. 11. Attach the two rubber strips between the base plate and cab frame (cab only). (Picture 4) 12. Attach the doors to the cab (cab only). Fit bolts 3 connectors behind grate Rubber strips Operator’s Manual City Ranger 2250...
Light: to connect the light on the trailer insert the cable plug from the trailer into the connector on City Ranger 2250. Check its function. Hydraulics: if the trailer has a hydraulic tipping function, connect the hydraulic hose to the snap coupling at the rear.
The hydraulic oil level can also be checked visually on the sight glass of the hydraulic tank (picture 4). Must be visible in the sight glass. (Picture 4) Topping-up – see maintenance section 3.4. Min. Max. Hydraulic oil – sight glass Operator’s Manual City Ranger 2250...
Page 35
Topping-up diesel Remove the coolant cover and check that the expansion tank is ¾ full. (Picture 3) Attention Never remove the water cover when the engine is hot. Diesel oil lamp Expansion tank – check coolant Operator’s Manual City Ranger 2250...
Speed is variably adjusted. See section 1.9. The function of the City Ranger 2250´s propulsion system · The City Ranger 2250 must be expected to have operating changes within the first 25-50 hours of its lifetime. · The City Ranger 2250 is developed with controlled deceleration.
Page 37
To protect the hydraulic system, it is important that the machine reaches operating temperature BEFORE the engine is operated at full power. Warning The City Ranger 2250 is articulated – it turns sharply, immediately. Turn the steering wheel carefully. Operator’s Manual City Ranger 2250...
Page 38
3. Push the brake pedal down (Picture 1), lift the parking lock up (Picture 2) and release the brake pedal (See Section 1.6). 4. Turn off the City Ranger 2250 by turning the key back to the key-release position. Operating with front attachments...
Service and maintenance 3.1 Daily maintenance Daily maintenance of the City Ranger 2250 is simple, easy and very important. Three things are required: Cleaning the water cooler, oil cooler and air filter, and cleaning of the condenser where air conditioning is fitted (See Section 3.3).
2. Clean the air filter housing with a clean cloth. (Picture 1) Warning Always switch off the engine before washing the machine. 3.2 Lubricating Cables and movable parts. Lubricate with a little oil approx. every 15 hours. Operator’s Manual City Ranger 2250...
5. Check that the oil fills half the sight glass when the oil is cold (maximum). Tank filter/hydraulic oil filter The City Ranger 2250 is fitted with a combined filter. The filter is replaced and filter housing cleaned during service. Operator’s Manual City Ranger 2250...
Engine oil check 1. Park the City Ranger 2250 on a level surface. Check the oil level 2. Check the oil level before the engine starts. (Picture 1) 3.
Page 45
API CF, CF-4, CG-4 or CH-4 engine oil classification. Never use special additives. Oil types Lubricating oil viscosity must be suitable for the ambient temperature range for the climate in which the machine is to operate. (Picture 1) Operator’s Manual City Ranger 2250...
Fuel tank The fuel tank is an integrated part of the cab around the seat and joystick console. Warning Never screw a bracket or other object onto the fuel tank. Operator’s Manual City Ranger 2250...
Page 47
1. Check for loose hose clamps – lubricate with a little oil on the clamp screw and tighten. 2. If hoses and hose clamps are worn, they should be immediately replaced. 3. Remove air from the fuel system, if fuel hoses have been replaced. Operator’s Manual City Ranger 2250...
C) Carefully replace the cooler cover. D) Start the City Ranger 2250 and run the machine until it is sufficiently warm. E) Switch the engine off and add more coolant. (Picture 1) Important –...
Described in section 3.1. 3.8 Air filter Cleaning the air filter A) When the City Ranger 2250 is operating in dirty and dusty conditions, open the vacuum valve every day to get Windscreen washer liquid cap rid of larger dirt and dust particles.
+ terminal is connected to the battery’s + terminal, and the - terminal is connected to the battery’s – terminal. Battery fluid level The level should be checked once a year. Only distilled water may be added. (Picture 1) Operator’s Manual City Ranger 2250...
Loosen the wheel nuts before the wheel is lifted off the ground. Jacking point: · for the rear wheel. (Picture 1) · for the front wheel. (Picture 2) When fitting the wheels, tighten the wheel nuts after the machine is lowered to the ground. Operator’s Manual City Ranger 2250...
The fitting of the new filter is carried out in reverse order: · filter element. Steel plate · steel plate. · foam plate. · grate. See picture 4 Filter element Filter Steel plate Foam plate Grate Operator’s Manual City Ranger 2250...
Conditions 4.1 Warranty The warranty period for the materials and manufacture of this City Ranger 2250 is 12 months from the date of purchase. In case of errors or defects on the machine within the warranty period, Nilfisk Outdoor Division will carry out the necessary repairs without charge for materials and working hours in accordance with the terms and conditions listed below.
Nilfisk Outdoor Division, Nilfisk A/S 4.3 Disposal When, many years from now, your City Ranger 2250 has reached the end of its working life, it should be disposed of in a responsible manner that conforms with relevant disposal regulations. 1. Used hydraulic oil, engine oil, diesel oil, coolant and AC coolant are to be delivered at an approved waste disposal facility or site.