JUKI MEB-3200 Engineer's Manual page 171

No. Function
I6 Plural times knife 13, knife
length 2nd time
I7 Plural times knife 13,
remainder cut amount
I8 Plural times knife 14, knife
length 1st time
I9 Plural times knife 14, knife
length 2nd time
J0 Plural times knife 14,
remainder cut amount
J1 Plural times knife 15, knife
length 1st time
J2 Plural times knife 15, knife
length 2nd time
J3 Plural times knife 15,
remainder cut amount
J4 Plural times knife 16, knife
length 1st time
J5 Plural times knife 16, knife
length 2nd time
J6 Plural times knife 16,
remainder cut amount
K6 Plural times knife, gimp and
bobbin thread haul delay time
K7 Plural times knife, multicutting
delay time
K8 Plural times knife, multicutting
cloth chip chute time
K9 Plural times knife, multicutting
ON cloth cutting knife position
L0 Plural times knife, parallel
section knife adjustment
value 0
L1 Plural times knife, parallel
section knife adjustment
value 1
L2 Plural times knife, parallel
section knife adjustment
value 2
L3 Plural times knife, parallel
section knife adjustment
value 3
L4 Plural times knife, parallel
section knife adjustment
value 4
L5 Plural times knife, parallel
section knife adjustment
value 5
L6 Plural times knife, parallel
section knife adjustment
value 6
L7 Plural times knife, parallel
section knife adjustment
value 7
L8 Plural times knife, parallel
section knife adjustment
value 8
L9 Plural times knife, parallel
section knife adjustment
value 9
(Caution) Memory switch Nos. 40 to 50 and L0 to L9 are set in "15 - (8) ADJUSTING THE CLOTH CUTTING
KNIFE PRESSURE".
Description
2nd time knife length of knife No. 13
Remainder cut length between eyelet and
parallel section of knife No. 13
1st time knife length of knife No. 14
2nd time knife length of knife No. 14
Remainder cut length between eyelet and
parallel section of knife No. 14
1st time knife length of knife No. 15
2nd time knife length of knife No. 15
Remainder cut length between eyelet and
parallel section of knife No. 15
1st time knife length of knife No. 16
2nd time knife length of knife No. 16
Remainder cut length between eyelet and
parallel section of knife No. 16
Time from gimp and bobbin thread haul to
bobbin thread trimming ON at the time of
long thread trimming
Time from multicutting ON to start of lowering
of cloth cutting knife
Time from dust chute ON to move of feed
base at the time of multicutting ON
Cloth cutting knife lifting position to make
multicutting ON
Plural times knife, knife adjustment value of
parallel section 0 (Knife holder No. 0)
Plural times knife, knife adjustment value of
parallel section 1 (Knife holder No. 1)
Plural times knife, knife adjustment value of
parallel section 2 (Knife holder No. 2)
Plural times knife, knife adjustment value of
parallel section 3 (Knife holder No. 3)
Plural times knife, knife adjustment value of
parallel section 4 (Knife holder No. 4)
Plural times knife, knife adjustment value of
parallel section 5 (Knife holder No. 5)
Plural times knife, knife adjustment value of
parallel section 6 (Knife holder No. 6)
Plural times knife, knife adjustment value of
parallel section 7 (Knife holder No. 7)
Plural times knife, knife adjustment value of
parallel section 8 (Knife holder No. 8)
Plural times knife, knife adjustment value of
parallel section 9 (Knife holder No. 9)
167
−
Standard Setting range
value
8 5 to 38
5 0 to 20
18 10 to 38
8 5 to 38
5 0 to 20
18 10 to 38
8 5 to 38
4 0 to 20
18 10 to 38
8 5 to 38
4 0 to 20
150 0 to 1000
100 0 to 1000
200 0 to 1000
1000 0 to 1500
20 –100 to 300
0 –100 to 300
0 –100 to 300
0 –100 to 300
0 –100 to 300
0 –100 to 300
0 –100 to 300
0 –100 to 300
0 –100 to 300
0 –100 to 300
−
Unit Level
mm 1
mm 1
mm 1
mm 1
mm 1
mm 1
mm 1
mm 1
mm 1
mm 1
mm 1
ms 2
ms 2
ms 2
Pulse 2
Pulse 1
Pulse 1
Pulse 1
Pulse 1
Pulse 1
Pulse 1
Pulse 1
Pulse 1
Pulse 1
Pulse 1