JUKI MEB-3200 Engineer's Manual page 102

Setting itm
Data No.
Needle thread tension
40
Compensation of needle thread tension
41
at right parallel section
42 Compensation of needle thread tension
at left parallel section
Compensation of needle thread tension
43
of eyelet
Compensation of needle thread tension
44
at right bottom of eyelet
Compensation of needle thread tension
45
at left bottom of eyelet
Compensation of needle thread tension
46
at right taper bar
Compensation of needle thread tension
47
at left taper bar
Compensation of needle thread tension
48
at straight bar
49 Compensation of needle thread tension
at right round bar
Compensation of needle thread tension
50
at left round bar
Compensation of needle thread tension
51
at sewing start
Compensation of needle thread tension
52
at sewing end
Compensation of needle thread tension
53
at the time of thread trimming
Compensation of needle thread tension
54
at the time of stop
55
56
57
58
59
Looper thread tension
60
Compensation of looper thread tension at
61
right parallel section
Compensation of looper thread tension at
62
left parallel section
Compensation of looper thread tension of
63
eyelet
Compensation of looper thread tension at
64
right bottom of eyelet
65 Compensation of looper thread tension at
left bottom of eyelet
Compensation of looper thread tension at
66
right taper bar
Compensation of looper thread tension at
67
left taper bar
Compensation of looper thread tension at
68
straight bar
69 Compensation of looper thread tension at
right round bar
Compensation of looper thread tension at
70
left round bar
Compensation of looper thread tension at
71
sewing start
Compensation of looper thread tension at
72
sewing end
Compensation of looper thread tension at
73
the time of thread trimming
Compensation of looper thread tension at
74
the time of stop
75
76
77
78
78
79
Writing No.
80
81 Cut length compensation
Plural times selection
82
Decorative buttonhole offset
83
Setting range
0 to 180
-180 to 180
-180 to 180
-180 to 180
-180 to 180
-180 to 180
-180 to 180
-180 to 180
-180 to 180
-180 to 180
-180 to 180
-180 to 180
-180 to 180
-180 to 180
-180 to 180
0 to 180
-180 to 180
-180 to 180
-180 to 180
-180 to 180
-180 to 180
-180 to 180
-180 to 180
-180 to 180
-180 to 180
-180 to 180
-180 to 180
-180 to 180
-180 to 180
-180 to 180
1 to 99 (0 to 99 by memory switch)
0 to cut length - knife length
0 : Knife holder without step eyelet
1 : Decorative buttonhole
2 : Knife holder with step eyelet
3 : Knife holder with step eyelet only
0 to cut length – knife length
98
− −
Description
Needle thread tension value (Standard of individual needle
thread tension)
Compensation value of needle thread tension at right side of
parallel section (Difference in terms of No=40)
Compensation value of needle thread tension at left side of
parallel section (Difference in terms of No=40)
Compensation value of needle thread tension at top of eyelet
(Difference in terms of No=40)
Compensation value of needle thread tension at right side of
bottom of eyelet (Difference in terms of No=40)
Compensation value of needle thread tension at left side of
bottom of eyelet (Difference in terms of No=40)
Compensation value of needle thread tension at right side of
taper bar (Difference in terms of No=40)
Compensation value of needle thread tension at left side of
taper bar (Difference in terms of No=40)
Compensation value of needle thread tension at straight bar
(Difference in terms of No=40)
Compensation value of needle thread tension at right side of
round bar (Difference in terms of No=40)
Compensation value of needle thread tension at left side of
round bar (Difference in terms of No=40)
Compensation value of needle thread tension at sewing start
(Difference in terms of No=40)
Compensation value of needle thread tension at sewing end
(Differnce in terms of No=40)
Compensation value of needle thread tension at the time of
thread trimming of the sewing machine (Difference in terms
of memory switch 7)
Compensation value of needle thread tension at the time of
stop of the sewing machine (Difference in terms of memory
switch 9)
Looper thread tension value (Standard of individual looper
thread tension)
Compensation value of looper thread tension at right side of
parallel section (Difference in terms of No=60)
Compensation value of looper thread tension at left side of
parallel section (Difference in terms of No=60)
Compensation value of looper thread tension at top of eyelet
(Difference in terms of N0=60)
Compensation value of looper thread tension at right side of
bottom of eyelet (Difference in terms of No=60)
Compensation value of looper thread tension at left side of
bottom of eyelet (Difference in terms of No=60)
Compensation value of looper thread tension at right side of
taper bar (Difference in terms of No=60)
Compensation value of looper thread tension at left side of
taper bar (Difference in terms of No=60)
Compensation value of looper thread tension at straight bar
(Difference in terms of No=60)
Compensation value of looper thread tension at right side of
round bar (Difference in terms of No=60)
Compensation value of looper thread tension at left side of
round bar (Difference in terms of No=60)
Compensation value of looper thread tension at sewing start
(Difference in terms of No=60)
Compensation value of looper thread tension at seing end
(Difference in terms of No=60)
Compensation value of looper thread tension at the time of
thread trimming of the sewing machine (Difference in terms
of memory switch 8)
Compensation value of looper thread tension at the time of
stop of the sewing machine (Difference in terms of memory
switch 10)
Writing pattern No.
(At the time of No. = "0", data is deleted.
Compensation value of cloth cut length in terms of No. 2
Cut length at the time of plural times motion of knife
Method of selecting cloth cutting at the time of plural times
motion of knife
Offset position of cloth cutting when selecting decorative
buttonhole at the time of plural times motion of knife