JUKI MEB-3200 Engineer's Manual page 111

No Function
50 Knife motor adjustment value 0
*
51 Position where pulse can start knife motor jump feed
52 Position where pulse can start knife motor thread
trimming
53 Number of pulses of plural times knife move of knife
motor
54 Position of pulse of plural times knife jump feed of
knife motor
55 Stop time of knife motor in lower position
56 Number of pulses of knife motor move
57 Number of low speed pulses of lowering knife motor
58 Number of low speed pulses of raising knife motor
59 Knife motor move speed
63 Number of low speed pulses of plural times knife
lowering of knife motor
64 Number of low speed pulses of plural times knife
raising of knife motor
65 Needle thread clamp with/without
66 Number of stitches of needle thread clamp open
67 Lowering timing of needle thread clamp
68 Needle thread clamp lowering delay time
69 Lengthwise move amount from sewing end of needle
thread clamp closing (Caution) 2
70 Jump feed speed of crosswise axis
71 Jump feed speed of lengthwise axis
72 Jump feed speed of turning axis
73 Jump feed speed of thread trimming of crosswise
axis
74 Jump feed speed of thread trimming of lengthwise
axis
75 Jump feed speed of thread trimming of turning axis
86 Needle thread trimming ON, lengthwise traveling
amount
87 Long thread trimming, lengthwise position of start of
turning of turning axis
88 Long thread trimming, angle compensation of turning
axis
89 Long thread trimming, gimp haul ON delay time
90 Angle of sewing end of round bar
91 Round bar setting
92 Delay time of looper thread hauling of long thread
trimming
93 Double action of looper thread hauling of long thread
trimming
94 Presser/start SW replacement
95 Delay time of needle thread clamp closing
96 Temporary stop time of needle thread clamp
97 Cloth cutting overlap time
98 Cloth presser open delay check selection
99 Cloth presser/cloth cutting offset selection
A0 Cloth cutting knife 1, width of eyelet
A1 Cloth cutting knife 1, length of eyelet
A2 Cloth cutting knife 2, width of eyelet
A3 Cloth cutting knife 2, length of eyelet
A4 Cloth cutting knife 3, width of eyelet
A5 Cloth cutting knife 3, length of eyelet
A6 Cloth cutting knife 4, width of eyelet
A7 Cloth cutting knife 4, length of eyelet
A8 Cloth cutting knife 5, width of eyelet
A9 Cloth cutting knife 5, length of eyelet
B0 Cloth cutting knife 6, width of eyelet
B1 Cloth cutting knife 6, length of eyelet
B8 Needle thread haul two-step selection
B9 Needle thread haul OFF delay
C0 Lengthwise axis needle thread clamp jump feed
speed
C1 Throat plate looper thread trimming ON lengthwise
move amount
E0 Sewing feed control mode
(Caution) 2. At the time of No.B8=1 : set to 14.
* In case of the machine with multicutting device, No. with the asterisk becomes the adjustment value of the motor to actuate
the knife to cut the eyelet section.
Description
Adjustment value 0 of number of pulses of knife
moving at the time of cloth cutting (Knife holder No.
0)
Position of pulse of start of crosswise/
lengthwise jump feed at the time of cloth
cutting
Position of pulse of start of thread trimming at the
time of cloth cutting
Number of pulses of plural times knife move at the
time of cloth cutting
Position of pulse of plural times knife lengthwise jump
feed at the time of cloth cutting
Stop time from reaching lower position to starting
lifting
Number of pulses of knife moving at the time of cloth
cutting
Numbrer of low speed pulses when knife lowering
finished at the time of cloth cutting
Number of low speed pulses when knife raising starts
at the time of cloth cutting
Knife move speed at the time of cloth cutting
Number of low speed pulses when plural times knife
lowering finished at the time of cloth cutting
Number of low speed pulses when plural times knife
raising starts at the time of cloth cutting
0 : Without 1 : With
Number of stitches to turn ON needle thread open
from sewing start
Time from presser origin move to needle thread
clamp lowering
Time until needle thread clamp lowers.
Y move amount from sewing end of needle thread
clamp closing
Speed of crosswise axis at the time of jump feed
Speed of lengthwise axis at the time of
jump feed
Speed of turning axis at the time of jump feed
Speed of crosswise axis at the time of jump feed of
thread trimming
Speed of lengthwise axis at the time of
jump feed of thread trimming
Speed of turning axis at the time of jump
feed of thread trimming
Lengthwise traveling amount from end
of sewing to needle thread trimming ON
Long thread trimming, Lengthwise position of start
of turning of turning axis
Long thread trimming, Angle compensation pulse of
turning axis ... standard 125˚
Long thread trimming, Delay time from turning of
turning axis to gimp haul ON
Angle of sewing end of round bar
0 : Round bar setting not permitted, 1 : Round bar
setting permitted
Time from looper thread haul OFF to looper thread
trimming OFF
0 :1 time 1 : 2 times
0 : Normal 1 : Presser/start SW replacement
Time from needle thread clamp closing to raising
Time from needle thread clamp raising to resuming
of feed
Start time of cloth cutting knife motion before reaching
cloth cut position
0 : Move at the start of sewing after cloth open delay
1 : Simultaneously
0 : Normal (64 mm), 1 : 10 mm offset (54 mm)
Knife No. = 1 of width of eyelet
Knife No. = 1 of length of eyelet
Knife No. = 2 of width of eyelet
Knife No. = 2 of length of eyelet
Knife No. = 3 of width of eyelet
Knife No. = 3 of length of eyelet
Knife No. = 4 of width of eyelet
Knife No. = 4 of length of eyelet
Knife No. = 5 of width of eyelet
Knife No. = 5 of length of eyelet
Knife No. = 6 of width of eyelet
Knife No. = 6 of width of eyelet
0 : Normal, 1 : 2 steps of needle thread haul motion
Delay time from needle thread haul OFF to thread
clamp
Lengthwise jump feed speed from end of sewing to
the position of needle thread clamp
Move amount from end of sewing to throat plate
looper thread trimming
0 : Feed end 1 : Feed center 2 : Feed start reference
107
− −
Standard value Setting range
30 pulses -100 to 300
S, J, C, T types : 400 pulses 0 to 1500
R type : 0 pulses
1020 pulses 0 to 1500
1130 pulses 0 to 1500
800 pulses 0 to 1500
50ms 50 to 500
1130 pulses 500 to 1500
60 pulses 0 to 300
80 pulses 80 to 300
4800 pps 50 to 9990
60 pulses 0 to 300
80 pulses 80 to 300
0 0 to 1
5 0 to 99
0 -100 to 100
100 0 to 1000
23 0 to 50
1000pps 50 to 5000
S, R, T types : 2000pps 50 to 5000
J, C types : 5000pps
500pps 50 to 2000
1000pps 50 to 5000
S, R, T types : 2000pps
50 to 5000
J, C types : 3000pps
S, R types : 900pps 50 to 2000
J, C, T types : 2000pps
S, R, J, C types : 4 mm 0 to 50
T type : 3 mm
10mm 0 to 16
0 pulse -30 to 30
0ms 0 to 1000
-5˚ -120 to -5
1 0 to 1
0 0 to 500
0 0 to 1
0 0 to 1
50 0 to 1000
50 0 to 1000
S, R, T types : 0 ms 0 to 200
J, C types : 100 ms
S, R, T types : 0 0 to 1
J, C types : 1
S, R types : 0 0 to 1
J, C, T types : 1
2.1mm 1.0 to 4.0
3.2mm 1.0 to 8.0
2.5mm 1.0 to 4.0
3.8mm 1.0 to 8.0
2.9mm 1.0 to 4.0
4.4mm 1.0 to 8.0
3.0mm 1.0 to 8.0
4.6mm 1.0 to 4.0
3.2mm 1.0 to 8.0
5.4mm
1.0 to 4.0
2.7 mm 1.0 to 4.0
5.1 mm 1.0 to 8.0
0 0 to 1
50ms 0 to 1000
S, R types : 1,000 pps 50 to 5000
J, C types : 1,500 pps
T type : 800 pps
10mm 0 to 50
1 0 to 2
Unit Level
1 pulse 1
1 pulse 2
1 pulse 2
1 pulse 2
1 pulse 2
10ms 1
1 pulse 2
1 pulse 1
1 pulse 1
10pps 2
1 pulse 1
1 pulse 1
– 1
Number of 1
stitches
10 ms 2
10 ms 2
1 mm 2
10pps 2
10pps 2
10pps 2
10pps 2
10pps 2
10pps 2
1mm 2
1mm 2
1 pulse 2
10ms 2
˚ 2
– 2
10 ms 2
– 2
– 2
10 ms 2
10 ms 2
10 ms 2
– 2
– 2
0.1mm 2
0.1mm 2
0.1mm 2
0.1mm 2
0.1mm 2
0.1mm 2
0.1mm 2
0.1mm 2
0.1mm 2
0.1mm 2
0.1mm 2
0.1mm 2
– 1
10ms 2
10pps 2
1mm 2
– 2