Introduction And Installation; Heatersteam (Ur*); Dimensions And Weights; When Opening The Packaging - Carel heaterSteam User Manual

1.1 HeaterSteam (UR*)

Range of isothermal electric heater humidifi ers for steam production
control and distribution, fi tted with graphic display.
Available models (identifi ed by means of the code on the label, packaging
and on the technical data plate):
•
UR002, UR004, UR006, UR010, UR013 with steam production capacity
up to 13 kg/h (28,66 lb/h), water connections under the base of the
humidifi er;
•
UR020, UR027, UR040, UR053, UR060, UR080 with steam production
capacity from 20 to 80 kg/h (from 44.09 to 176.37 lb/h), water
connections next to the humidifi er.

1.2 Dimensions and weights

Models UR002..UR013
A
B
C
Fig. 1.a
UR002...13
A 365 (14.37)
Size
B 275 (10.82)
mm (in)
C 712 (20.03)
UR002...13
packaged 31(68.3)
Weights
empty 26(57.3)
kg (lb)
installed* 35(77.1)
* in operating conditions, fi lled with water.

1.3 When opening the packaging

•
check the integrity of the humidifi er upon delivery and notify to the
carrier immediately, in writing, any damage that can be attributed to
improper or careless transport;
•
move the humidifi er to the installation site before removing it from the
packaging, grasping the neck from beneath;
•
open the cardboard box, remove the protective material and remove
the humidifi er, keeping it upright at all times.

1.4 Positioning

•
the unit is designed for wall mounting, suitable to support the weight
under operating conditions (see par. "Wall mounting"). The models
UR020*... UR080 * can be fl oor installed;
•
to ensure proper distribution of steam, place the humidifi er next to the
steam distribution point;
•
position the humidifi er vertically, use a spirit level to ensure the base is
perpendicular; observe the minimum clearances (see Fig. 1.b) to allow
space for maintenance.
Caution: during operation, the external metal panels heat up, and
the back leaning against the wall can reach temperatures above 60 °C
(140 °F).

1. INTRODUCTION AND INSTALLATION

Models UR020...UR080
A
B
C
UR020...40 UR053...80
690 (27.16) 876 (34.48)
445 (17.51) 445 (17.51)
888 (34.96) 888 (34.96)
Tab. 1.a
UR020...40 UR053...80
73(160.9) 98(216.0)
63(138.8) 87(191.8)
97(213.8) 155(341.7)
Tab. 1.b
Models UR002..UR013
≥200
(7.9")
≥200
≥200
(7.9")
(7.9")
<0,5
≥700
(27.6")
≥400
(15.7")

1.5 Wall mounting

Mount the humidifi er on the wall using the support bracket pre-attached
to the humidifi er, using the screws kit supplied (for mounting dimensions
see draws below).
Instructions for fastening:
1. unscrew the wall bracket from the one attached to the humidifi er;
2. secure the bracket to the wall (see Fig. 1.c), checking with a spirit level
the horizontal position; if the unit is mounted on a masonry wall, you
can use the plastic anchor plugs (Ø 8 mm, Ø 0.31in) and the screws
(Ø 5 mm x L= 50 mm, Ø 0.19 in x L= 1.97 in) supplied;
3.
hang the humidifi er on the bracket using the profi le on the upper
edge of the unit's rear (Fig. 1.d).
4. lock the humidifi er to the wall by means of the hole / holes found /
on the lower part of the rear panel of the machine (Fig. 1.d).
61 201 235,5 285,5
(2.39) (7.92) (9.27) (11.24)
169 32 137
(6.67) (1.25) (5.39)
230 416 230
(9.06) (16.38) (9.06)
365 (14.37)
49 (1.91) 49 (1.91)
67 67 67 67
(2.64) (2.64) (2.64)
(2.64)
162 106
(6.38) (4.17)
7 "heaterSteam" +0300080EN - rel. 1.0 - 27.04.2016
ENG
Models UR020...UR080
≥200
(7.9")
≥300
≥500
(11.8")
(19.7")
≥700
(27.6")
Fig. 1.b
122,5 445 122,5
93
(4.82) (17.52) (4.82)
(3.67)
22,5 22,5
(0.89) (0.89)
145 400 145
(5.71) (15.75) (5.71)
Fig. 1.c
Fig. 1.d