Supervisor Network; Supervisor Network Protocols And Confi Guration; Table Of Supervisor Variables - Carel heaterSteam User Manual

11.1 Supervisor network protocols and
confi guration
The humidifi er can be connected to a supervisor via serial (BMS) or
Ethernet network. The Carel, ModBus and BACnet protocols are supported
as standard by the units.
M9 M2 M8
1 2 1 2 3 4 5 6 7 8 1 2
Fig. 11.a
Port Terminal on c.pHC controller Protocol
BMS (1) M12.1, M12.2, M12.3
Ethernet (2)

11.2 Table of supervisor variables

The variables shown in the lists below are only a set of all the internal variables on the heaterSteam humidifi er.
DO NOT CONFIGURE ANY VARIABLES THAT ARE NOT SHOWN IN THE TABLES TO AVOID RISKING INCORRECT HUMIDIFIER OPERATION.
11.2.1 Table of Carel variables
Below are the variables used by the Carel protocol.
Integer variables
Variable Variable name
1 SV_SWVer
2 SV_OSVer
3 UnitModel
4 Conductivity
5 WirelessPrbInfo_1.BattLev
6 WirelessPrbInfo_1.RadioSignalLev
7 WirelessPrbInfo_2.BattLev
8 WirelessPrbInfo_2.RadioSignalLev
9 WirelessPrbInfo_3.BattLev
10 WirelessPrbInfo_3.RadioSignalLev
11 WirelessPrbInfo_4.BattLev
12 WirelessPrbInfo_4.RadioSignalLev
13 UnitStatus
14 WorkHr
15 CylWorkHr
19 RegulationCfg.RegTyp
20 ThrshAlrmDT
21 MainPrbCfg.Typ
22 LimitPrbCfg.Typ
23 WHardnessMan
24 EvapCycleNoThrshsh
25 FillTScale
26 DilDrainTScale
27 Scheduler.SchedDayToSet
28 SchedDayCfg[0].StartHr
29 SchedDayCfg[0].StartMin
30 SchedDayCfg[0].WorkMode
31 SchedDayCfg[1].StartHr
32 SchedDayCfg[1].StartMin
33 SchedDayCfg[1].WorkMode
34 SchedDayCfg[2].StartHr
35 SchedDayCfg[2].StartMin
36 SchedDayCfg[2].WorkMode
37 SchedDayCfg[3].StartHr
38 SchedDayCfg[3].StartMin
39 SchedDayCfg[3].WorkMode
40 SchedDayCfg[4].StartHr
41 SchedDayCfg[4].StartMin
42 SchedDayCfg[4].WorkMode
43 SchedDayCfg[5].StartHr
44 SchedDayCfg[5].StartMin
45 SchedDayCfg[5].WorkMode
46 UoM

11. SUPERVISOR NETWORK

M12 M1 M5 M6
3 2 1 1 2 1 2 1 2 3
Ethernet
1
2
Carel, ModBus, BACnet, Carel retro
ModBus, BACnet
Tab. 11.a
R/W
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
To confi gure supervision on the BMS port (1), go to "SETTINGS –
SUPERVISION", specifi cally screens Eh01, Eh02 and Eh03.
If connecting the supervisor to the Ethernet port (2), set the network
parameters (DHCP, IP address, subnet mask, gateway, DNS) on screen
Eh04.
For other supervisor protocols, select the Carel protocol on the BMS serial
port and use the Carel external gateway (supernode for humidifi cation:
SNU0000EM0) combined with the desired supervision card (depending
on the protocol).
Note: Ethernet CAT-5 STP cable, maximum length 100 m. To connect
the shield, use the earth connector provided on the controller.
Note: for BMS and Fieldbus, use shielded cables with the shield
connected to earth.
Description
Software version
OS version
Model version
Conductivity
Wireless probe 1: battery level
Wireless probe 1: wireless signal level
Wireless probe 2: battery level
Wireless probe 2: wireless signal level
Wireless probe 3: battery level
Wireless probe 3: wireless signal level
Wireless probe 4: battery level
Wireless probe 4: wireless signal level
Unit status
Unit operating hours
Cylinder operating hours
Control type
High humidity/temperature alarm delay
Main probe type
Limit probe type
Manual water hardness value (if WHardnessTyp is TRUE)
Number of evaporation cycles (0=auto)
Variation in fi ll time
Variation in drain time
When >0, day of the week to be confi gured (1=Monday, 7=Sunday)
Band 1 start hours
Band 1 start minutes
Band 1 operating mode
Band 2 start hours for
Band 2 start minutes
Band 2 operating mode
Band 3 start hours
Band 3 start minutes
Band 3 operating mode
Band 4 start hours
Band 4 start minutes
Band 4 operating mode
Band 5 start hours
Band 5 start minutes
Band 5 operating mode
Band 6 start hours
Band 6 start minutes
Band 6 operating mode
Unit of measure
47
Category
Unit info
I/O
Wireless probes
Unit status
Reg
Alrm T
Probes cfg
Unit cfg
Scheduler setting
UoM
"heaterSteam" +0300080EN - rel. 1.0 - 27.04.2016
ENG