Specification Table (Cm/Cb-140Ge/140Ge-Ra) - IAI cm-140ge User Manual

CM-140GE / -RA/-UV / CB-140GE / -RA

11.2. Specification table (CM/CB-140GE/140GE-RA)

Specifications
Scanning system
Frame rate full frame
Pixel clock
Line frequency
CCD sensor
Sensing area
Cell size
Active pixels
Pixels in video output.
Full Scan
2/3 partial Scan
1/2 partial Scan
1/4 partial Scan
1/8 partial Scan
Vertical Binning
Region-of-interest (ROI)
Sensitivity on sensor (minimum) 0.08 Lux (Max. gain, Shutter OFF, 50%
S/N ratio
Digital Video output.
Iris video output. Analogue
Gain
Synchronization
GPIO Module
Input/output switch
Clock Generator ( One)
Pulse Generators ( Four)
Hardware Trigger modes
Optical Black area transfer mode
Event message
Electronic Shutter
Preset Shutter speed
Programmable exposure
Exposure Time (Abs)
GPIO plus Pulse Width
Control interface
Functions controlled via GigE
Vision Interface
GigE Vision Streaming Control
Indicators on rear panel
Operating temperature
Humidity
Storage temp/humidity
Vibration
Shock
Regulatory
CM-140GE / 140GE-RA
31.08 frames/sec. Progressive (1052 lines/frame)
32.696kHz (1H = 30.584 µs, (1988 pixel clock/line)
1/2". Monochrome ICX267AL
6.4 (h) x 4.8 (v) mm 1/2 inch diagonal
1392 (h) x 1040 (v) 31.08 fps. H = 32.696 kHz
1392(h) x 694 (v) 39.97 fps
1392 (h) x 520 (v) 46.57 fps. H = 32.696 kHz
1392 (h) x 260 (v) 61.92 fps. H = 32.696 kHz
1392 (h) x 130 (v) 73.97 fps. H = 32.696 kHz
1392 (h) x 520 (v) 48.86 fps. H = 25.753 kHz ( *Note)
User Definable. Memory read-out
*Note: Vertical binning is for CM-140GE only
video )
GigE Vision Compliant
Mono8,Mono10,Mono10_Packed
0.7 V p-p , enabled by internal switch
Manual -3 to +24 dB (1 step=0.0358dB)
Configurable 14-in / 9-out switch
12-bit counter based on 25MHz clock or Pixel clock
20-bit counter programmable for length, start point, stop point, repeat
Pre-Select (PS), Pulse Width (PW), RCT, Frame Delay and Sequence
SYNC / ASYNC mode ( Trigger mode status when exposure starts )
Exposure start, Exposure end, Trigger IN, Video start, Video end
OFF(1/31) and 1/60 to 1/10,000 in 9 steps
2L (61.2µs) to 1052L (32.2ms) in 1L steps
µsec – user definable. Same range as PE
max. 2 sec (Can be set by 100µs unit or Pixel Clock unit)
Register based. GigE Vision / GenICam compliant
Shutter, Gain, Black Level, Trigger mode, Read out mode,
GPIO setup ,ROI ( GenICam mandatory functions )
Packet size, Delayed ( Frame ) read-out, inter-packet delay
Jumbo frame can be set at max. 4K(4040) , Default packet size is 1428 Byte.
Power, Hardware trigger, GigE Link, GigE activity
-25C to +60C/20% to 90% non-condensing
CE (EN61000-6-2 and EN61000-6-3), FCC part 15 class B, RoHS, WEEE
- 60 -
CB-140GE / 140GE-RA
Progressive scan
65 MHz
1/2" Bayer Color ICX267AK
4.65 (h) x 4.65(v) m
1392 (h) x 1040 (v)
H= 32.696 kHz
0.42 Lux (Max. gain, Shutter OFF,50%
Green, w/IR cut filter)
More than 50 dB (0dB gain)
GigE Vision Compliant
BAYRG8,BAYGB8,BAYRG10,BAYGB10
Internal X-tal
ON / OFF
-5C to +45C
20 – 90% non-condensing
10G (20Hz to 200Hz, XYZ)
70G