Download  Print this page

Adjusting The Clock; Before Operation - Sanyo DC-F450 Instruction Manual

Hide thumbs

Advertisement

i
ADJUSTING THE CLOCK
Using the remote control
5.
Example: To set "PM 7:30",
1.
Press the CLOCK button. The clock display appears,
After connecting the mains lead for the first time, when you press
the CLOCK button, the clock display blinks.
6.
2,
Press the ADJUST button.
\l/
AM 12:00
The hours display blinks.
3,
Press the + or – TUNING/TIME
SET button to set the "hours."
\l/
PM 7:00
Press the + or – TUNINGfHME
SET button to set the "minutes."
\l/
PM 7:30
Press the ADJUST button. The clock starts,
PM 7:30
-
The time can be set accurately by pressing the ADJUST button
when a time signal is heard.
These operations
can be done, even if in standby.
To display the clock during operation, press the CLOCK button. Press
it again to return to the original display.
When the display blinks because of a power failure, reset the time.
4.
Press the ADJUST button.
\l/
PM 7:00
The minutes display blinks.
BEFORE OPERATION
Turning the power on and off
Press the POWER
button. The indicators
and displays
light and the
STANDBY indicator goes out. (After connecting the mains lead, when you
press the POWER
button for the first time, the volume
reset feature
automatically
reduces the volume level. )
To turn off the power, press the POWER button again. The STANDBY
indicator lights. The clock display remains lit.
When the mains lead is connected to the AC outlet, the STANDBY
indicator lights and the unit will respond to commands from the remote
control,
Smart start function
If the following buttons are pressed when the unit is in standby, the unit
turns on automatically
and the selected function is set,
CD player section
PLAY/PAUSE,
DISC 1, DISC 2, DISC 3,
OPEN/CLOSE
Tuner section
BAN D
Cassette section
, DECK A ONLY <
Selecting the function
Press the FUNCTION button to select the desired function. The selected
function indicator lights in red.
The function is automatically
selected when CD play or tape playback is
started, or when the BAND button has been pressed (except during
recording or tape dubbing),
When the function selection is changed, CD play or tape playback is
automatically
stopped.
Adjusting the volume
Turn the VOLUME control, or press the+ or – FRONT VOL button on the
remote control,
Adjusting the Iefth'ight speaker balance
Use the BALANCE control to adjust the Iefthight speaker balance.
Adjusting the sound quality
Turn the SPECTRUM CONTROL to LOW to increase the Iowfrequencies.
Turn the control to HIGH to increase the high frequencies.
To reduce the volume temporarily
(muting)
Press the MUTE button on the remote control. "MUTE" blinks on the
display.
To restore the previous volume setting, press the MUTE button again.
"MUTE" disappears.
Bass expander
system
Press the BASSXPANDER
button to enhance the bass sound. "BASS"
appears on the display.
The initial setting of this function is ON.
Selecting the sound mode
Press the SOUND PRESET button to select the sound mode matching the
music to be listened to.
POP: Pops, etc.
ROCK: Rock music, etc.
CLASSIC:
Classical music, etc.
JAZZ: Jazz, etc.
Spectrum
analyzer
Indicates the input level and peak value of each sound range,
Demonstration
mode
If the DISPLAY button is pressed, the display enters the demonstration
mode. The following display modes will sequentially
appear,
AMP—
CD ~
TUNER
TAPE
To cancel this mode, press the DISPLAY button again.
To turn the changer mechanism
lights off
While pressing the MEMORY button, press the DISPLAY button.
To turn the lights on, repeat step above.
WHAT TO DO IF ...
If the operation of the unit or display is not normal or when all the memoty
contents are to be cleared, disconnect the mains lead from the AC outlet,
then press the RESET button (rear of the unit) for 30 seconds or more.
6

Advertisement

loading

  Related Manuals for Sanyo DC-F450