Sanyo DC-F450 Instruction Manual page 8

ii
CD PLAY
Use compact discs bearing the symbol shown below. In addition to
conventional 12 cm CDs, this system can be used to play8 cm CDs without
an adatXer.
KIim
DIGITAL AUDIO
Note:
Do not touch the disc tray while it is moving.
Never place anything except a compact disc on the disc tray, Foreign
objects can damage the unit.
Do not apply excessive force to the disc tray.
Discs must be placed on the disc tray one at a time.
I
If discs are loaded, you can turn the unit on and begin play immediately
by pressing the PLAY/PAUSE, DISC 1, DISC 2 or DISC 3 button.
1.
2.
3.
Select "CD function by pressing the FUNCTION button. "CD" appears
onthedisplay, then"CD is replaced by ''diSC". "I''discn umberblinks,
Press one of the disc select buttons (DISC 1, DISC 2 or DISC 3), then
press the OPEN/CLOSE button,
If the changer mechanism has detected "no disc" for the disc
select button pressed, the tray slides out automatically.
The selected disc tray slides out. "OPEN" appears and the selected
disc number blinks on the display.
Place the disc with the label facing up on the disc tray.
\'
\\
For 12 cm CD
For 8 cm CD
4.
5.
6.
7.
Press the OPEN/CLOSE button again to close the disc tray,
Note:
To open or close the disc tray, be sure to use the OPEN/CLOSE
button. Do not touch the disc tray by hand.
Repeat steps 2-4 to load another disc.
Press one of the disc select buttons (DISC 1, DISC 2 or DISC 3).
The selected disc indicator blinks.
17El
34
5,78
b'
"D" appears, and play starts from the first track of the selected disc.
The track number and elapsed play time for the current track are
displayed.
Also, the whole track numbers (up to track 16) on the disc are
displayed on the music calendar.
When playing tracks numbered 17 or higher, no track number
appears on the music calendar.
If the desired disc number has been selected, the PLAY/PAUSE
button can also be used to start play.
Note:
If the disc is loaded with the label facing downward, or if a badly
scratched disc is loaded, "NO dlSC" appears on the display.
If this occurs, load the disc correctly or replace the damage disc.
Press the STOP button to end disc play.
When the last track of the last disc has been played, the player stops
automatically.
When the OPEN/CLOSE button is pressed during play, play will stop
and the disc tray will slide out.
Ejecting or replacing discs
1. While in the CD play or stop mode, press one of the disc select buttons
to be ejected, then press the OPEN/CLOSE button.
While the player is playing one disc, you can eject or replace
another disc without stopping play.
2. Remove or replace the disc.
3. Press the OPEN/CLOSE button.
Notes on handling compact discs
Do not expose the disc to direct sunlight, high humidity or high
temperatures for extended periods of time.
Discs should be returned to their cases after use,
Do not apply paper or write anything on the disc surface,
Handle the disc by its edge, Do not touch the playing surface (glossy
side).
Fingerprints and dust should be carefully wiped off the playing surface
of the disc with a soft cloth.
Wipe in a straight motion from the centre to the outside of the disc.
Never use chemicals such as record cleaning sprays, antistatic
sprays or fluids, benzene or thinner to clean compact discs.
To start play from the desired track
Using the remote control
1. Select the desired disc by pressing the DISC SELECT button, then
press the button on the CD controls.
2. Press two number buttons to select the desired track.
Using the main unit
1. Press the desired DISC button, then press the STOP button.
2. Select the desired track by using the SKIP/SEARCH buttons, then
press the PLAY/PAUSE button.
Temporarily stopping play
Press the PLAY/PAUSE button. " D " blinks on the display. To resume
play, press the button again.
Skip play
To skip to track 6 while track 3 is playing, press the >/ EN SKIP/
SEARCH button repeatedly until "6" appears in TRACK on the display.
To skip back to track 3 while track 6 is playing, press the K< /<< SKIP/
SEARCH button repeatedly until "3 appears,
The number buttons on the remote control can also be used for skip
play. To skip to track 6 while one track is playing, press O, then 6.
Search (forward/reverse)
If the >/ Flor14< /<< SKIP/SEARCH button is pressed during play,
the player will search at high speed in the forward or reverse direction
while the button is being pressed, When the button is released, normal
play will continue.
Introscan
Press the INTRO button on the remote control to play the first 10 seconds
of each track. "INTRO appears on the display.
Press the INTRO button again to return to normal play.
Introscan play will not function during random play or programmed
play,
Random play
Press the RANDOM button on the remote control to begin random play.
The player will automatically select and play discs and tracks at random.
"RANDOM" appears on the display.
Random play will not function during introscan play or programmed
play.