Checking The Callsign Setting - Kenwood TH-D74A User Manual

Setting by Local CQ
1 Press [ ] (1s).
The destination selection screen appears. This screen also
appears when selecting [Destination Select] in the Digital
Function Menu.
2 Select [Local CQ] and press [ENT].
CQCQCQ is set to [TO].
Setting by Gateway CQ
1 Press [ ] (1s).
The destination selection screen appears. This screen also
appears when selecting [Destination Select] in the Digital
Function Menu.
2 Select [Gateway CQ] and press [ENT].
The repeater list selection screen appears.
3 Select the destination repeater and press [ENT].
The repeater is set to [TO].
Setting by Individual
1 Press [ ] (1s).
The destination selection screen appears. This screen also
appears when selecting [Destination Select] in the Digital
Function Menu.
2 Select [Individual] and press [ENT].
The Callsign list appears.
3 Select the Callsign and press [ENT].
The selected Callsign is set to [TO].
Setting by Reflector
1 Press [ ] (1s).
The destination selection screen appears. This screen also
appears when selecting [Destination Select] in the Digital
Function Menu.
2 Select [Reflector] and press [ENT].
The Reflector menu item appears.
3 Select the following items and press [ENT].
[Use Reflector]: If your repeater is currently linked
to a reflector, select [Use Reflector] and press [ENT].
[CQCQCQ] is set to [TO]. Then press [PTT] to transmit
your digital voice signal to the reflector.
[Link to Reflector]: If you want to link the repeater to a
reflector, or you want to change to another reflector, select
[Link to Reflector] and press [ENT]. Input the reflector
number/module, and press [A/B]. [REFXXXXL] is set to
[TO]. Then press [PTT] to link the repeater to the reflector.
Up to 5 reflectors you linked before are shown when you
select [Link to Reflector] again.
[Unlink Reflector]: If you want to link the repeater
to another reflector, be sure to unlink currently linked
reflector. Select [Unlink Reflector] and press [ENT].
[_______U] is set to [TO]. Then press [PTT] to unlink the
repeater from the reflector.
[Echo Test]: You can verify how well your digital voice
signal is getting into the system. Select [Echo Test] and
press [ENT]. Then [_______E] is set to [TO]. Then press
[PTT] to transmit your digital voice signal to the system.
After releasing [PTT], echo back will be sent back from the
repeater.
[Repeater Info.]: You can send the repeater information
command. Select [Repeater Info.] and press [ENT]. Then
[_______I] is set to [TO]. Then press [PTT] to transmit
the repeater information command. After releasing [PTT],
repeater ID will be sent from the repeater.
Note:
◆ When you want to add a simplex DV Access Point's frequency
information in the repeater list (Menu No.210) for using the DR
mode Reflector menu above, input the string "DIRECT" both for
[Callsign] and [Gateway] entry fields. Please refer to "Adding
the Repeater List" for details.
Setting by Call History
1 Press [ ] (1s).
The destination selection screen appears. This screen also
appears when selecting [Destination Select] in the Digital
Function Menu.
2 Select [Call History] and press [ENT].
The Callsign list appears.
3 Select the destination Callsign and press [ENT].
The selected Callsign is set to [TO].
Setting by Direct Input (URCALL)
1 Press [ ] (1s).
The destination selection screen appears. This screen also
appears when selecting [Destination Select] in the Digital
Function Menu.
2 Select [Direct Input(URCALL)] and press [ENT].
The direct input screen appears.
3 Enter the destination Callsign and press [ENT].
The destination Callsign is set to [TO].
Note:
◆ When entering the destination Callsign by direct input
(URCALL), the route setting is not automatically set. Please
be sure to set the route setting by [Route Select] in the Digital
Function Menu then.
Setting EMR
1 Press [ ] (1s).
The destination selection screen appears. This screen also
appears when selecting [Destination Select] in the Digital
Function Menu.
2 Select [EMR] and press [ENT].
The EMR is set.

CHECKING THE CALLSIGN SETTING

You can check transmission settings of DV/DR mode before
transmission.
1 Select [CS Setting] in the Digital Function Menu.
The confirmation screen appears.
2 Press [A/B].
Each press switches between name display and Callsign
display.
16-8