Dcs - Kenwood TH-D74A User Manual

CTCSS Frequency Scan
This function scans through all CTCSS frequencies to identify
the incoming CTCSS frequency on a received signal. You
may find this useful when you cannot recall the CTCSS
frequency that the other persons in your group are using.
1 Press [TONE] 2 times to activate the CTCSS function.
• The < icon appears on the display when the
>
CTCSS function is On.
• Each time you press [TONE], the selection changes as
follows:
Tone ( ) ➡ CTCSS (
Tone ( : default) ➡ Off (no display).
Additionally, when APRS is ON and Voice Alert is
configured, Voice Alert ON is added to the above cycle.
2 Press [F], [TONE] (1s).
"
• Scan starts and Scanning
To quit the scan, press [ ].
•
• When a CTCSS frequency is identified, the identified
frequency appears on the display and blinks.
3 Press [A/B] to program the identified frequency in place of
the currently set CTCSS frequency.
• The CTCSS function will remain On. To cancel CTCSS,
press [TONE] until CT no longer appears on the display.

DCS

Using DCS
1 Select your desired band.
2 Press [TONE] 3 times to activate the DCS function.
• The < icon appears on the display when the DCS
>
function is on.
• Each time you press [TONE], the selection changes as
follows:
Tone ( ) ➡ CTCSS (
Tone ( : default) ➡ Off (no display).
Additionally, when APRS is ON and Voice Alert is
configured, Voice Alert ON is added to the above cycle.
) ➡ DCS ( ) ➡ Cross
"
blinks on the display.
) ➡ DCS ( ) ➡ Cross
3 Press [F], [TONE].
• The current DCS code appears on the display and
blinks.
4 Select your desired DCS code.
• Refer to the table below for the available codes.
5 Press [A/B] to complete the setting.
6 When you are called: The transceiver squelch opens
only when the selected DCS code is received.
When you make a call: Press and hold [PTT], then
speak into the microphone.
• To cancel DCS, press [TONE] until DCS no longer
appears on the display.
023 025 026
051 053 054
114 115 116
143 145 152
174 205 212
245 246 251
266 271 274
332 343 346
411 412 413
452 454 455
506 516 523
612 624 627
703 712 723
DCS Code Scan
This function scans through all DCS codes to identify the
incoming DCS code on a received signal. You may find it
useful when you cannot recall the DCS code that the other
persons in your group are using.
1 Press [TONE] 3 times to activate the DCS function.
• The < icon appears on the display when the DCS
>
function is on.
• Each time you press [TONE], the selection changes as
follows:
Tone ( ) ➡ CTCSS (
Tone ( : default) ➡ Off (no display).
Additionally, when APRS is ON and Voice Alert is
configured, Voice Alert ON is added to the above cycle.
10-2
DCS Code
031 032 036 043
065 071 072 073
122 125 131 132
155 156 162 165
223 225 226 243
252 255 261 263
306 311 315 325
351 356 364 365
423 431 432 445
462 464 465 466
526 532 546 565
631 632 654 662
731 732 734 743
) ➡ DCS ( ) ➡ Cross
047
074
134
172
244
265
331
371
446
503
606
664
754