Sheet Metal Unit Replacement - GMC G Service Manual

3. Wheelhouse panel to radiator support bolts (49) (fig­
ure 9).
Tighten
• Bolts to 17 N*m (13 ft. lbs.).
4. Radiator support to fender bolts (119) (figure 8).
If f l Tighten
• Bolts to 17 N»m (13 ft. lbs.).
5. Sheet metal support to the vehicle.
6. Sheet metal support to radiator support bolts.
H 3 Tighten
• Bolts to 17 N»m (13 ft. lbs.).
• Radiator support to frame nuts (80) to 47 N»m
(35 ft. lbs.).
7. Lower radiator grille panel to the vehicle.
8. Grille to the vehicle.
9. Primary hood latch bracket to the radiator support
bolts.
\j? \ Adjust
• Hood latch left or right so that the hood properly
engages the hood latch.
f ^ l Tighten
• Bracket to radiator support bolts to 27 N*m (20
ft. lbs.).
10. Air cleaner inlet to the radiator support.
11. Fuel vapor canister to the radiator support.
12. Ground wires to the radiator support.
13. Headlamp assemblies.
14. Headlamp bezels.
15. Headlamp and parking lamp wiring harness to the
radiator support.
16. Headlamp and parking lamp wires to the lamps.
17. Battery.
• Refer to ENGINE ELECTRICAL (SEC. 6D).
18. Air conditioning condenser.
• Refer to AIR CONDITIONING (SEC. 1B).
19. Radiator.
• Refer to RADIATOR (SEC. 6B2).
SHEET METAL UNIT
REPLACEMENT
h"»| Remove or Disconnect
Tool Required:
J 24595-B Door Trim Pad Remover.
1. Hood.
• Refer to "Hood Replacement" earlier in this
section.
SHEET METAL 2B-11
2. Battery.
• Refer to ENGINE ELECTRICAL (SEC. 6D).
3. Radiator.
• Refer to RADIATOR (SEC. 6B2).
4. Air conditioning condenser.
• Refer to AIR CONDITIONING (SEC. 1B).
5. Headlamp and parking lamp wires from the lamps.
6. Headlamp and parking lamp wiring harness from the
radiator support.
7. Ground wires from the radiator support.
8. Fuel vapor canister from the radiator support.
9. Air cleaner inlet from the radiator support.
10. Bumper from the vehicle.
• Refer to FRAME AND BUMPERS (SEC. 2A).
11. Wheelhouse panel to fender bolts (50) (figure 9).
12. Fender to cowl bolts (47) (figure 8).
13. Upper fender to door pillar bolt (48).
14. Wheelhouse panel to shield bolts.
15. Shield to underbody retainers using J 24595-B (figure
10).
16. Shield from the vehicle.
17. Lower fender to door pillar bolt (45).
18. Radiator support to frame nuts (80), lower retainers
(79), lower cushions (78), upper cushions (76),
retainers (75), bolts (73), and washers (74) (figure
12
).
19. Sheet metal assembly.
• With the aid of a helper, lift the sheet metal from
the chassis.
[*<-| Install or Connect
1. Sheet metal assembly.
• With the aid of a helper, lift the sheet metal onto
the chassis.
2. Radiator support to frame washers (74), bolts (73),
retainers (75), upper cushions (76), lower cushions
(78), lower retainers (79), and nuts (80) (figure 12).
3. Lower fender to door pillar bolts (45) (figure 8).
l iX l Tighten
• Bolt to 43 N«m (31 ft. lbs.).
4. Shield to the vehicle.
5. Shield to underbody retainers.
6. Wheelhouse panel to shield bolts.
7. Upper fender to door pillar bolt (48) (figure 8).
R I Tighten
r
• Bolt to 43 N»m (31 ft. lbs.).