Norac UC5 Installation Manual
Spray height control system display kit for trimble fmx
Hide thumbs
Also See for UC5:
- Operator's manual (68 pages) ,
- Installation manual (50 pages) ,
- Instruction manual (35 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Norac UC5
Summary of Contents for Norac UC5
- Page 1 Trimble FMX Display Kit Installation Manual 54VT-TB-FMX...
- Page 2 Reorder P/N: 54VT-TB-FMX-INST Rev B (Trimble FMX Display Kit) NOTICE: NORAC Systems International Inc. reserves the right to improve products and their specifications without notice and without the requirement to update products sold previously. Every effort has been made to ensure the accuracy of the information...
-
Page 3: Table Of Contents
ITEM C26: 43240-26 – Cable UC5 Switch Box ......................9 ITEM C40: 43260-30 – Cable UC5 Interface DTM 4 Pin 12in Stub ..............10 ITEM C41: 43220-03 - Cable UC5 Network 14 AWG - 3M ................11 ... -
Page 4: Introduction
1 Introduction The Trimble FMX Display Kit Manual is intended to be used in conjunction with the UC5 Spray Height Control Installation Manual. This manual provides instructions to interface the UC5 Control Module to the Trimble FMX Display. For installation of the rest of the UC5 Spray Height Control System please refer to the sprayer specific manual provided with the kit. -
Page 5: Installation
2 Installation The following instructions are for installation on a self-propelled sprayer (Section 2.1) or pull type sprayer (Section 2.2). Self-Propelled 1. Securely mount the control module (E01) inside the sprayer cab. 2. Tee the CANbus interface cable (C40) between the Trimble cable 75834 and the ISOBUS trunk cable that runs to the back of the sprayer. -
Page 6: Pull Type
Pull Type 2.2.1 Control Module on Tractor (Non-ISOBUS Ready Tractor) 1. Securely mount the control module (E01) inside the tractor cab. 2. Tee the CANbus interface cable (C40) between Trimble cable 75834 and Trimble cable 77368. 3. Connect the 6 pin Deutsch plug on cable C40 to the end of the control module with only one Deutsch connector. - Page 7 2.2.2 Control Module on Tractor (ISOBUS Ready Tractor) 1. Securely mount the control module (E01) inside the tractor cab. 2. Tee the CANbus interface cable (C40) between Trimble cable 75407 and Trimble cable 92752. 3. Connect the 6 pin Deutsch plug on cable C40 to the end of the control module with only one Deutsch connector.
- Page 8 Name Quantity 43260-29 CABLE UC5 INTERFACE DT 4 PIN 12 IN STUB 1. Securely mount the control module (E01) on the sprayer near the CANbus connection. 2. Tee the CANbus interface cable (C42) between Trimble cable 77368 and the IBRC connector.
-
Page 9: Switch Box Installation
Switch Box Installation The switch box is an optional component to make the operation of the UC5 easier. An extra label is provided if the operator would like to remove the switches from the box and mount them in another location. -
Page 10: Cable Drawings
3 Cable Drawings ITEM C25: 44602-01 – Switch Remote Hand Control... -
Page 11: Item C26: 43240-26 - Cable Uc5 Switch Box
ITEM C26: 43240-26 – Cable UC5 Switch Box... -
Page 12: Item C40: 43260-30 - Cable Uc5 Interface Dtm 4 Pin 12In Stub
ITEM C40: 43260-30 – Cable UC5 Interface DTM 4 Pin 12in Stub... -
Page 13: Item C41: 43220-03 - Cable Uc5 Network 14 Awg - 3M
ITEM C41: 43220-03 - Cable UC5 Network 14 AWG - 3M... - Page 14 Canada NORAC Systems International Inc. Phone: (+1) 306 664 6711 Toll Free: 1 800 667 3921 Shipping Address: 3702 Kinnear Place Saskatoon, SK S7P 0A6 United States NORAC, Inc. Phone: (+1) 952 224 4142 Toll Free: 1 866 306 6722...