Onkyo DV-SP1000 Instruction Manual page 94

Troubleshooting
SACD audio is not output
by the i.LINK sockets?
SACD audio is not output
by the analog audio out-
puts?
Can't access the Analog
Audio Out settings?
Can't play MP3 and JPEG
discs?
Can't select MP3 files?
Can't view JPEG files?
The message "NO PLAY"
appears on the display?
Buttons on the remote con-
troller don't work?
Buttons on the
DV-SP1000/DV-SP1000E
work OK but those on the
remote controller don't?
94
This is because the i.LINK Output Setting is
set to Off. If the DV-SP1000/DV-SP1000E is
properly connected to an i.LINK component
and an SACD is loaded, the IEEE 1394 indica-
tor will flash.
The i.LINK cables are not connected properly.
This is because the i.LINK Output Setting is
set to On.
While the i.LINK Output Setting is set to On,
the Analog Audio Out Speaker Setting,
Speaker Distance, and Test Tone settings have
no effect and are unavailable.
The disc is not ISO 9660 Level 2 format.
The disc has not been finalized.
MP3 files without a ".mp3" or ".MP3" file-
name extension are not recognized.
The MP3 disc is a multisession disc.
JPEG files without a ".jpg" or ".JPG" or
".JPEG" filename extension are not recog-
nized.
Only Baseline JPEG files are supported. Pro-
gressive JPEG files are not.
Only JPEG files with the following brightness/
color difference ratios are supported: 4:4:4,
4:2:2, and 4:1:1.
The JPEG file is too big.
The disc is dirty.
Power supply voltage fluctuations and other
anomalies, such as static electricity, can inter-
fere with normal operation.
There are no batteries in the remote controller. Install new batteries (page 14).
The batteries are flat.
The batteries are installed incorrectly.
You're not pointing the remote controller at the
DV-SP1000/DV-SP1000E's remote sensor.
You're too far away from the DV-SP1000/
DV-SP1000E.
A strong light source is interfering with the
DV-SP1000/DV-SP1000E's remote sensor.
If the DV-SP1000/DV-SP1000E is installed in
a cabinet with colored glass doors, the remote
controller may not work reliably when the
doors are closed.
Set the i.LINK Output Setting to On (page 76).
Check the i.LINK connections and correct as nec-
essary (page 35).
Set the i.LINK Output Setting to Off (page 76).
Set the i.LINK Output Setting to Off (page 76).
Use only ISO 9660 Level 2 format discs (page 10).
Finalize the disc (page 10).
Use the correct filename extension (page 10).
Only files in the first session of a multisession disc
can be played (page 10).
Use the correct filename extension (page 10).
Use Baseline JPEG files (page 10).
Use JPEG files with the supported ratio (page 10).
Use JPEG files that are less than 5 MB (page 10).
Remove the disc and clean it (page 11).
Turn off the DV-SP1000/DV-SP1000E, wait five
seconds, then turn it on again. If that doesn't
resolve the issue, disconnect the power cord from
the wall outlet, wait five seconds, reconnect it, then
try again.
Replace with new batteries (page 14).
Check the batteries and correct as necessary
(page 14).
Point the remote controller at the DV-SP1000/
DV-SP1000E's remote sensor (page 14).
Use the remote controller closer to the
DV-SP1000/DV-SP1000E (page 14). The remote
controller has a range of approximately 16 ft. (5
meters).
Make sure that the DV-SP1000/DV-SP1000E is
not subjected to direct sunshine or inverter-type flu-
orescent lights. Relocate if necessary.
Open the doors, or use a cabinet without colored
glass.