Learning The Commands Of Other Remote Controllers - Onkyo DV-SP1000 Instruction Manual

Controlling Other Components
ON
ON
1
4
7
+ 10
SEARCH
S
DVD
MODE
DVD
ZOOM ON
AUDIO
SEL
+
CH
ZOOM
L MODE
-
DISPLAY
LAST MEMORY
REC LM
AUDIO
AUDIO
REPEAT
REPEAT
VIDEO INPUT VIDEO OFF
V IN
OPEN/CLOSE
Learning the Commands of Other
Remote Controllers
The DV-SP1000/DV-SP1000E's remote controller can
learn individual commands from other component's
remote controllers and then be used to control those
components. Commands can be learnt by the dedicated
leaning buttons—[L1], [L2], [L3], and [L4]—or any but-
ton. Each button can learn up to four commands, one for
each remote controller mode: DVD, Amp, VCR, and TV.
If you've entered a control code for a component
(page 86) and certain buttons don't work as expected,
you can also use this function to program those buttons
individually.
1
Point the remote controllers at each other,
about 2 to 6 inches (5–15 cm) apart.
2–6" (5–15 cm)
2
While holding down the [DVD], [AMP],
[VCR], or [TV] MODE button, press the
[ON] button, and then release both but-
tons.
The MODE button and Tx/Learn indicator light
up.
STANDBY
TV
I INPUT
+
2 3
TV CH
-
5 6
8 9
TV VOL
0
CLEAR
MEMORY DIMMER AMP INPUT
M D
INPUT
AMP INPUT
V1 V 2 V3
MODE
AMP VCR TV
PICTURE
CONTROL
ENTER VOL
MUTING
STEP/SLOW RANDOM
RD
SUBTITLE ANGLE RESOLUTION
SBTTL ANGLE RSLTN
A-B ASPECT
A-B
ASPECT
LEARNING
V OFF L1 L 2
L 3 L 4
RC-563DV
RC-563DV
3
On the DV-SP1000/DV-SP1000E's remote
controller, press the button that you want
to learn the new command.
The Tx/Learn indicator goes off while the button
is being pressed, and comes back on again when
it's released.
Use the dedicated leaning buttons—[L1], [L2],
[L3], and [L4]—or another button.
4 On the other remote controller, press and
hold the button whose command you want
to learn until the Tx/Learn indicator
flashes.
If the command is learnt successfully, the Tx/
Learn indicator flashes slowly twice, and then the
MODE button and Tx/Learn indicator remain lit.
If the Tx/Learn indicator flashes quickly three
times, the command has not been learnt, in which
case you should try again from step 3.
If the Tx/Learn indicator flashes quickly six times,
the remote controller's memory is full and no
more commands can be learnt.
5 To learn more new commands, repeat
steps 3 and 4.
When you've finished, press the MODE button
that you pressed in step 2.
To use the learnt command, select the relevant
mode, and then press the button.
Notes:
• The following buttons cannot learn new commands:
[LIGHT] and the [DVD], [AMP], [VCR], and [TV]
MODE buttons.
• Learning mode is cancelled automatically if you don't
press any buttons for 30 seconds.
• The DV-SP1000/DV-SP1000E's remote controller
comes preprogrammed with the commands necessary
for controlling Onkyo DVD players (DVD mode) and
AV receivers (Amp mode). However, you can repro-
gram individual buttons if necessary. The original
commands can be restored by resetting the remote
controller.
• To program a button that has already learnt a com-
mand, repeat this procedure. The previously learnt
command will be overwritten.
• Like most remote controllers, the DV-SP1000/
DV-SP1000E's remote controller uses infrared. Com-
mands from remote controllers that don't use infrared
cannot be learnt.
• When the remote controller's batteries expire, all
learnt commands may be lost and will have to be learnt
all over again, so keep your other remote controllers in
a safe place.
91