Onkyo DV-SP1000 Instruction Manual page 19

Getting to Know the DV-SP1000/DV-SP1000E
VIDEO OUT S VIDEO (30)
These two sockets output S-Video and can be con-
nected to an S-Video input on a TV or projector.
VIDEO OUT VIDEO (30)
These two sockets output composite video and can
be connected to a composite video input on a TV or
projector.
DIGITAL 1 AUDIO OUT (36, 38)
These sockets output digital audio and can be con-
nected to the digital audio input on a hi-fi amp, AV
receiver, surround sound decoder (Dolby Digital,
DTS), or other component. There's a coaxial output
and an optical output.
DIGITAL 2 AUDIO OUT (36, 38)
These sockets output digital audio and can be con-
nected to the digital audio inputs on a hi-fi amp, AV
receiver, surround sound decoder (Dolby Digital,
DTS), or other component. There's a coaxial output
and an optical output.
IR IN/OUT (40)
The IR IN socket can be used to connect a commer-
cially available IR receiver, which can be used to
pickup signals from the remote controller when the
DV-SP1000/DV-SP1000E is located in another
room, installed in a rack, or is out of range of the
remote controller
The IR OUT connector can be used to connect a
commercially available IR emitter, which can be
used to pass remote controller signals received by
the IR IN along to other components.
REMOTE CONTROL (40)
These (Remote Interactive) sockets can be con-
nected to the sockets on other Onkyo AV com-
ponents for interactive control.
To use you must make an analog audio connec-
tion between the DV-SP1000/DV-SP1000E and
your Onkyo AV receiver, even if they are connected
digitally.
D.MIX AUDIO OUT (30, 31, 38)
These sockets output analog audio and can be con-
nected to a stereo analog audio input on a TV, hi-fi
amp, or other component. If the source audio is
multichannel (Dolby Digital, DTS, DVD-Audio,
SACD), they output a 2-channel downmix.
FRONT, SURR 1, CENTER & SUBWOOFER
AUDIO OUT (37)
These sockets output 5.1-channel analog audio and
can be connected to a 5.1-channel analog audio
input on an AV receiver, surround sound decoder
(Dolby Pro Logic), or other component.
SURR 2 AUDIO OUT (37)
These sockets output the same analog audio as the
SURR1 outputs and can be connected to the analog
surround back left and right inputs on a 7.1-channel
AV receiver or other component. When using these
sockets, the SURR MODE switch should be set to
1+2.
SURR MODE (AUDIO OUT) switch (37)
This switch is used to set the surround output mode
of the analog multichannel audio outputs. If you
connect the SURR 2 outputs to a 7.1-channel AV
receiver or amp, set this switch to 1+2. This reduces
the output level by 3 dB. If you're not using the
SURR 2 outputs, set this switch to 1.
AV CONNECTOR (32)
This SCART socket outputs RGB video, S-Video,
composite video, and analog stereo audio and can
be connected to the SCART socket on a TV, projec-
tor, or other component.
HD VIDEO OUT COMPONENT (31)
These BNC sockets output HD component video
and can be connected to the HD component video
input on an HDTV or projector.
When a video signal is fed to a VIDEO IN socket
(S-Video or composite), and the video input source
is set to EXTERNAL, that video signal is upcon-
verted to progressive and output here.
12V TRIGGER IN
This socket can be connected to the 12-volt trigger
output on an AV receiver or other component so that
the DV-SP1000/DV-SP1000E can be turned on
remotely.
AC INLET (41)
The supplied power cord should be connected here.
19