4.12.1 Emg Contact; 4.12.2 Fault Contact; 4.12.3 Call Contact; Connecting Emg Microphone - Bosch Plena Installation And User Instruction Manual

Plena Voice Alarm System | Installation and User Instructions | Installation

4.12.1 EMG contact

The EMG contact is activated on entering the
emergency state. The emergency state is entered when
the EMG button is pressed (see section 6.6) or when an
EMG trigger input is activated (see section 4.7.1).

4.12.2 Fault contact

The fault contact is activated on entering the fault state
(see section 7.1). The fault state is entered when a line
fault (see section 7.2.1) or a system fault (see section
7.2.2) occurs.

4.12.3 Call contact

The call contact is activated on entering the call state.
The call state is entered when:
• On one of the call stations the PTT button has been
pressed for making a business call (see section 6.5.2).
• An emergency (see section 4.7.1) or business trigger
(see section 4.7.2) input is activated.
• The EMG button on the controller has been pressed
for making an emergency or alert message (see
section 6.6.1).
4. 1 3

Connecting EMG microphone

On the front of the controller there is one connector for
an emergency (EMG) microphone.
figure 4. 1 6: Connecting the EMG microphone
Bosch Security Systems | 2004-06 | 9922 141 10371en
Pl en
a Vo
ice Al
ar m
Co nt
ro lle
0 dB Fau lt r
Indic
-6dB ator s
-20d B Proc esso
Netw r reset
Call/ ork Main
Musi EM G s A Disa
c/Sp are Batte ry bled
Grou nd short Mess age B
Input EMG
mic Zone 1
RCP Zone
Rout er Zone 2 Fault
Zone 3
4
Zone 5 EMG
Alert Zone Ack
mess age 6
Alarm All call Rese
mess t
age Zon e sele
EMG ct
mic Indic ator
test
Sele ct Zon e1
CD/T
uner Zon e Zon
- sele ct e2
+ Aux
Zon e3
Alar m
Zon e4
- Zon e5
+
0
Zon e6
LBB1990/00
Voice Alarm Controller
4. 1 4

Connecting call stations

A call station (LBB1956/00) is connected to the
controller using a CAT-5 twisted pair RS-485 cable with
RJ45 connectors on each cable end. The controller has
two shielded RJ45 sockets allowing 2 call stations to be
directly connected to the controller. To connect more
call stations, use the two looped-through RJ45
connectors on a call station. Like this, in total, 8 call
stations can be part of a system. See figure 4.17 for
connection details.
V O X 10 k
6
S w itc 10 k
h
5
6
2 4 V
D C
ou t C a ll
s ta ti
o n
F o r s
e rv ic
e o n
ly
S E L
1
S E L
0
1
F ir m
w a re
U p g
S
ra d e
5
2
6
V O X
2 O ff
S w itc
h
O n
Im p e
d a n c
C a li
b r
figure 4. 1 7: Connecting call stations
If the cable between the call station and the voice alarm
controller is longer than 100 m, the call station must be
connected to a 24V(DC) power source. See figure 4.18
for connection details.
en | 41
Int Boos 1 Chann
Ext Boos ter el
ter BGM /Call 2 Chann
N.C./ Spare BGM el
A /Spar e
Call
Z1 100V
B Over ride/
0 Trigg er Outp
Z2 100V ut
100V
0 0 Z1 24V Trigger input/2
100V Z1 Emerg ency 4V DC out
Z3 100V 1 2
0 Z2 Z2 3 4
0 NC 5 6 24V
Z4 100V 100V Z3 COM EMG NC NO Busin 1 ess DC out
0 NO 2
0 Z3 Z4 NC COM 3 4
Z5 100V 100V COM Fault 5 6 Switch VOX 10k 10k
Z5 NO 1
0 0 Z4 NC 2 3
Z6 100V 100V COM 4
Z6 NO Call 5 6 24V
Ext Boos 0 0 Z5 NC DC out Call
ter 100V 100V TRG 1 24V statio n
In NO Volum e Overr For servi LBB
0 0 Z6 ide ce only 1990 /00
DC In 100V TRG2 Plena Voice 8900
24V SEL1 Max. outpu Alarm 199 0000
70V Int 1 SEL0 Moni Rated 115-2 outpu t powe r 360W Contr oller 1
Boos ter Out 2 1 Firmw APR tor S/N. 30V~ t powe r 240W
0 Out 3 4 Upgr are Supe mode , 50/60 Hz
100V 5 6 ade 2ch rvisio n Design 115V ~
Call VOX Switch 2 Off LBB oper ation The Nethe & Quality N663 230V
out In 1994 rlands ~
GND
On Appa ratus
USB Conn ected deliv ered
Off for 230V
Impe danc ~
Calib ration e On Firem an's
Exter nal Boos pane
ter L l Powe
Rate r
d input
CD/T GND LBB 1994 powe r:760
uner Line VA
AUX R T6.3 fuse
T10L L250 V for23
PC Vox 250V 0V AC
Spee ch filter for11 5V AC
Mic/ Line Phan Rem ote Cont
tom powe rol Pane
Off r l
Vox On
1
Digit Rout er
Mess age Moni toring al
2
Spea ker
War
This ning
appar atus
must be earthe
d
LBB1990/00
Voice Alarm Recorder
LBB1956/00
Call Station