Bosch Plena Installation And User Instruction Manual page 28

Plena Voice Alarm System | Installation and User Instructions | System units
12 Mains power inlet - A socket to connect the
mains power source to the router (see section 4.15).
13 Ground - A connection to electrically ground the
router.
14 Firmware upgrade connector - An RS232
connector to connect a PC to upgrade the firmware
of the router.
1
Plena Voice Alarm Router
Fault Indicators
0 dB
Processor reset
Network
-6dB
Call/EMG
-20dB
Music/Spare
Ground short
Input
5
1 Channel
Booster 1 BGM/Call
Booster 2
N.C./Spare
A
Z1 Z2 Z3 Z4 Z5 Z6
100V 0 100V 0 100V 0 100V 0 100V 0 100V 0 100V 70V 0 100V
100V 0 100V 0 100V 0 100V 0 100V 0 100V 0 100V 0
B
Z1 Z2 Z3 Z4 Z5 Z6
figure 3. 1 2: Front and rear views of the router (LBB1992/00)
16 Router connector - Two RJ45 connectors to
connect a controller or another router (see section
4.6).
17 Router ID - A rotary switch to set the ID of the
router (see section 5.6).
18 External booster 1 and 2 outputs - Two XLR
sockets to connect external booster 1 and 2 (see
section 4.15.3). These socket are respectively used in
combination with the Ext booster 1/2 in pins (no. 6
and 24).
19 ??? -
Bosch Security Systems | 2004-06 | 9922 141 10371en
2
A B
Zone1
Mains Zone2
Zone3
Battery
Zone4
Zone5
Zone6
6 7 8 9
Override/Trigger Output Trigger Input
Emergency
2 Channel
Z1 Z2 Z3 Z4 Z5 Z6
1
BGM/Spare
Call
24V
Booster 24V
V.O.R.
TRG1 TRG2 Failure DC Out Business
Booster 1 in Call out
1
NC NO
NC NO
COM 24V
Z1 Z2 Z3 Z4 Z5 Z6 1
+24V-
Booster 2 in
DC In TRG1 TRG2 Booster 24V V.O.R.
1
Failure DC Out
23 21 19
24 22 20
15 Configuration settings - Two DIP switches to
configure the router. A termination switch to identify
the last router in a row and a firmware upgrade
switch to enable firmware upgrading.
Zone select
Zone1 Zone2
Zone select
LBB 1992/00
2 3 4 5 6
Plena Voice Alarm Router
115-230V~,50/60Hz
10k 10k S/N.
2 3 4 5 6
Out
2 3 4 5 6
GND
Booster 2
Booster 1
2 3 4 5 6
18
20 24V DC output -
21 Booster failure - Two pins (NC relays) to report a
booster failure.
22 TRG1/2 - Two general purpose trigger outputs.
23 Backup power inlet - An inlet to connect a back-
up power supply to the router (see section 4.15.2).
24 External booster 2 input - Two input pins to
connect external booster 2 (70V/100V). These pins
are used in combination with the XLR socket Booster
2 Out (no. 18).
3
Zone3 Zone4 Zone5
4
10
115V~ 230V~
8900 199 20001
Apparatus delivered
Connected for 230V~
N663
Design & Quality
The Netherlands Rated input power:100VA
Line fuse:T1L250V for 230V AC
T2L250V for 115V AC
Router
Termination
In Firmware upgrade
ID
Off
Out
Warning
This apparatus must be earthde
On
1...9 Firmware Upgrade
17 16 15 14
en | 28
Alarm
Zone6
11 12
Power
13