Mounting The Plena Units; Connecting Routers; Connecting A Router To The Controller; Connecting A Router To A Router - Bosch Plena Installation And User Instruction Manual

Plena Voice Alarm System | Installation and User Instructions | Installation
• Installation and User Instructions Manual
• Configuration Software Manual
• Bosch data book
4.5

Mounting the Plena units

The Plena units (controller, router, BGM source and
external boosters) are suitable for table-top and 19-inch
rack mounting. For each unit, four feet (for table-top
use) and two mounting brackets (for 19-inch rack
mounting) are supplied. See figure 4.1 for installation
details.
P le n
a V o
ic e A
la rm
C o n
tr o lle
0 dB
r
Fa ult
Ind ica
-6d B tor s
-20 dB Pro ces
sor res
Ne two et
rk
Ca ll/E Ma ins
M G Dis ab
Mu sic Ba tter A
/Sp are y led
Gro und Me ssa B
ge
Inp ut sho rt
EM G Zon e1
mic
RC P Zon e2
Ro ute
r Zon e3 Fau lt
Zon e4
Zo ne5
EM G
Ale rt Zon e6 Ack
me ssa
ge
Ala rm All cal Re set
l
me ssa
ge
EM G
mic Ind ica
tor tes
t
Se lec
CD /Tu
ner
-
+
-
+
0
figure 4. 1 : 19-inch rack mounting
4.6

Connecting routers

To extend the total number of zones, extra routers
(LBB1992/00) can be connected to a voice alarm
system. Each router adds 6 extra speaker zones to be
served in the system. In total 6 extra routers can be
connected, allowing for 60 zones in total.
Bosch Security Systems | 2004-06 | 9922 141 10371en
Zo ne
se lec
t
t Zo ne
1
Zo ne
se lec Zo ne
2
Au x t
Zo ne
3
Ala rm
Zo ne
4
Zo ne
5
Zo ne
6
figure 4.2: Connecting routers
4.6.1 Connecting a router to the con-
troller
Plug the RJ45 connector on the one end of the router
cable into the Router output of the controller. Plug the
RJ45 connector on the other end of the cable in the
Router In input of the router.
4.6.2

Connecting a router to a router

Plug the RJ45 connector on the one end of the router
cable into the Router Out output of the router. Plug the
RJ45 connector on the other end of the cable in the
Router In input of the router.
4.6.3

Assigning a router ID

Each router must be assigned a unique ID. Use a small
screwdriver and turn the arrow, on the ID rotary switch,
towards the desired router ID (0 - 9).
4.6.4

Connecting trigger inputs

The rear of the router (and of the controller) provides
one terminal block for connecting trigger inputs. As for
en | 32
o n t r
o l P a
n e l
1
R o u t
e r
it o r in 2
g
e a k e
r
W a r
n i n g
T h is
a p p a
r a t u
s m u
s t b e
e a r t h
e d
a li ty
e th e
3
rl a n d
s
R a t e
R o u t d in p
e r L in e u t
f u s e
I D
In
T e r m
in a t io
n
F ir m
w a r e
u p
t e r 2
O u t
O f f
1 .. .9
O n
e th e a li ty
3
rl a n d
s
R a t e
R o u t
d in p
e r
L in e u t
f u s e
I D
In
T e r m
in a t io
n
F ir m
w a r e
t e r 2 u p
O u t
O f f
1 .. .9
O n