Appendix A: Comparison Of Rms Modules - Meyer Sound RMServer Hardware Manual

APPENDIX A: COMPARISON OF RMS MODULES

Table 3 documents the differences between the RMS modules. Loudspeakers with asterisks (*) come standard with the
RMS module.
Table 3: RMS Module
RMS Module LEDs
HP/MP Service LED (Red):
(PN 40.033.071.01) ■ Blinks once every 2 seconds if the
(Acheron 100, loudspeaker is connected to network
Acheron 80, Acheron LF,
and not yet discovered.
600-HP, 700-HP, 650-P,
■ Lights solid when the loudspeaker
DF-4, DS-2P, DS-4P,
* *
M2D-Sub , M3D ,
encounters an RMS hardware failure.
*
M3D-Sub , MICA*,
* *
MILO 60 , MILO 120 ,
Wink LED (Green):
MSL-4, MSL-6, MTS-4,
■ Lights solid when the loudspeaker is
PSM-2, PSW-2, PSW-4,
PSW-6, SB-1, SB-2,
winked from the RMS program.
SB-3F)
Activity LED (Green):
■ Flashes continuously when the loud-
speaker is discovered.
UltraSeries UX Service LED (Red):
(PN 40.084.008.01) ■ Blinks once every 2 seconds if the
(500-HP, JM-1P, M1D, loudspeaker is connected to network
* *
M1D-Sub , M'elodie ,
and not yet discovered.
MJF-212, MJF-212A,
■ Lights solid when the loudspeaker
UMS-1P, UPJ-1P,
encounters an RMS hardware failure.
UPJunior, UPM-1P,
UPM-2P, UPQ-1P,
Wink LED (Green):
UPQ-2P)
■ Lights solid when the loudspeaker is
UltraSeries UPM
winked from the RMS program.
(PN 40.076.028.01)
(Acheron Studio, M2D*,
Activity LED (Green):
UPA-1P, UPA-2P, UM-1P,
■ Flashes continuously when the loud-
UM-100P, USM-1P,
speaker is discovered.
USM-100P, USW-1P)
DX Wink/Activity LED (Green):
■ Blinks 10 ten times when powering up
(Acheron Designer,
MINA*, X-400C,
the loudspeaker.
*
MJF210 )
■ Unlit, after powering up, if the loud-
speaker is not discovered.
■ Flashes continuously when the loud-
speaker is discovered, and flashes
more rapidly with increased data activ-
ity.
MX Wink/Activity LED (Green):
(LEO-M*, 1100-LFC*, ■ Blinks 10 ten times when powering up
LYON)*
the loudspeaker.
■ Unlit, after powering up, if the loud-
speaker is not discovered.
■ Flashes continuously when the loud-
speaker is discovered, and flashes
more rapidly with increased data activ-
ity.
Buttons
Service Button:
■ Press to identify the loudspeaker on
the RMS network during the discovery
process.
■ Press and hold with the Reset button
to reset and undiscover the loud-
speaker.
Reset Button:
■ Press to reboot the RMS firmware
without discovering the loudspeaker.
■ Press and hold with the Service button
to reset and undiscover the loud-
speaker.
Service Button:
■ Press to identify the loudspeaker on
the RMS network during the discovery
process.
■ Press and hold with the Reset button
to reset and undiscover the loud-
speaker.
Reset Button:
■ Press to reboot the RMS firmware
without discovering the loudspeaker.
■ Press and hold with the Service button
to reset and undiscover the loud-
speaker.
Identify Button:
■ Press to identify the loudspeaker when
discovering.
■ Press to wink the discovered loud-
speaker.
■ Press and hold when powering up the
loudspeaker to undiscover it.
Identify Button:
■ Press to identify the loudspeaker when
discovering.
■ Press to wink the discovered loud-
speaker.
■ Press and hold when powering up the
loudspeaker to undiscover it.
RMS Network Mute
Connectors Enable
2 Weidmuller Jumper
connectors (pins J3)
2 Weidmuller Jumper
connectors (pins J3)
2 Weidmuller Recessed
connectors switch on
RMS user
panel
2 Weidmuller Jumper
connectors (pins J3)
55