Important Remarks Pag - Cardin Elettronica GL112409 Installation Manual

IMPORTANT REMARKS
READ THE FOLLOWING REMARKS CAREFULLY BEFORE PROCEEDING WITH THE INSTALLATION.
PAY PARTICULAR ATTENTION TO ALL THE PARAGRAPHS MARKED WITH THE SYMBOL
READING THESE IMPORTANT INSTRUCTIONS COULD COMPROMISE THE CORRECT WORKING
ORDER OF THE SYSTEM AND CREATE DANGER SITUATIONS FOR THE USERS OF THE SYSTEM.
• These instructions are aimed at professionally qualified "INSTALLERS
OF ELECTRICAL EQUIPMENT" and must respect the local standards
and regulations in force. All materials used must be approved and must
suit the environment in which the installation is situated.
• All maintenance operations must be carried out by professionally
qualified technicians. Before carrying out any cleaning or maintenance
operations make sure the power is disconnected at the mains.
• This appliance must be used exclusively for the purpose for which it
has been made. "i.e. for the automation of fold-up and overhead
garage doors" Any non authorised modifications are to be considered
improper and therefore dangerous. The manufacturer accepts no liability
for situations arising from an installation which does not conform to
the local standards and regulations in force and in particular when the
earthing circuit is not efficient.
• The programmer is fitted with an electrical input monitoring system, which
is used to block the motor in emergency conditions; however this system
is not active during the following stages:
- during the first 5 seconds of an opening stage starting from 'completely
closed'
- during the first 2.5 seconds of all other movement stages
Do not attempt to physically block the door during these stages,
otherwise you may risk blowing the motor circuit protection fuse "F3".
• After having installed the device (and before powering up the program-
mer) proceed as follows: release the door and move it manually, checking
that it moves smoothly and has no unusual points of resistance. Attach
the carriage to the chain guide and check that the opening travel limit is
activated by the carriage.
• Power up the electronic programmer: if the travel limit is active a flashing
dash will appear on the display indicating that the system is in pause
waiting for automatic reclosing. Activate the door in the manual mode
and close it using the "SEL" button. The door will move while the button
is pressed and stop when it is released.
Note: If you press the "PROG" button while you are closing the door manually
it will automatically move in the opening direction after the reclosing pause.
For more details see "manual operating mode" on page 13.
Caution! The only security devices which can block the move-
ment of the appliance while operating in the manual mode are
the blocking button and the travel limits. As soon as the door
is completely closed release the "SEL" button.
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law Caution! Always check that the chain is attached to the carriage
and the door is completely closed before starting programming.
• You are now ready to program the system, as described in the paragraph
"Programming procedure" on page 14, 15.
Note: If you need to check the status of the fuse "F2", disconnect the
power supply to the programmer; reconnect it only after having re-inserted
the fuse. Never exclude the travel limits ("programming procedure", note
2, pag. 14) and always check that the opening direction travel limits are
connected. Deceleration must be excluded for fold up doors (see "pro-
gramming procedure, note 3, pag. 14)
Caution! The presence of the electrical input monitoring system
does not exclude the need to install photoelectric cells or other
safety devices which are foreseen by the local standards and
regulations in force.
MINIMUM DISTANCE BETWEEN THE ROOF AND THE HIGHEST POINT REACHED BY THE DOOR
60 mm
Spring loaded
doors
IMPORTANT REMARKS
60 mm
Fold-up doors
10
Use
The unit GL112409 is suitable for spring loaded, fold up and counterbal-
anced garage doors (flush fitting or partially protruding) with maximum
dimensions of h=3m and L=3,5m and a maximum weight of 70kg.
Choose the kit according to the type of door (see accessories).
Technical description
- Motor powered by 24 Vdc.
- The reduction unit stator is made of die cast aluminium and contains a
never ending screw and a helicoidal crown wheel made of thermoplastic,
lubricated with permanently fluid grease.
- Two-piece chain housing made of plastic material which contains the
chain capstan and keeps it separate from the electronic parts.
- Electronic programmer with incorporated radio receiver.
- Courtesy light (E14 -230Vac - 40W)
- Shockproof plastic cover and base in opaline plastic.
Accessories
- 320/GL1124B
Kit for counter balanced garage doors complete with L 2100 mm chain
guide and curved adaptor arm "9"-"11" (fig. 6).
- 320/GL1124S
Kit for fold up and spring loaded doors complete with L 3150 mm chain
guide, curved lever , "10" (fig. 5), and a pair of drilled guide support
brackets "5" (fig. 3).
- 316/GL20SB
Manual release cord.
USER INSTRUCTIONS
Attention! Only for EU customers - WEEE marking.
This symbol indicates that once the products life-span has expired
it must be disposed of separately from other rubbish. The user
is therefore obliged to either take the product to a suitable dif-
ferential collection site for electronic and electrical goods or to
send it back to the manufacturer if the intention is to replace it
with a new equivalent version of the same product.
Suitable differential collection, environmental friendly treatment and disposal
contributes to avoiding negative effects on the ambient and consequently
All rights reserved. Unauthorised copying or use of the information contained in this docu
health as well as favouring the recycling of materials. Illicitly disposing of this
product by the owner is punishable by law and will be dealt with according
to the laws and standards of the individual member nation.
Important! Before starting the installation check that the structure to be
automated is in good working order and respects the local standards and
regulations in force. To this end make sure that the garage door is suf-
ficiently rigid (if necessary reinforce the structure) and check that the door
guide rails slide freely (we advise you to lubricate all moving parts). Check
that the minimum distance between the open door and the ceiling is not
less than 60 mm (fig. 1).
Caution! The chain guide must be positioned between 10 and
20 mm above the upper edge of the door. This position will guar-
antee optimum operation and will ensure that the garage door
does not grate against the chain guide during (fig. 1 det. A)
60 mm
Counterbalanced
doors
IMPORTANT REMARKS
. NOT
10 - 20 mm
A
1