Table of Contents
Advertisement
IMPORTANT REMARKS
READ THE FOLLOWING REMARKS CAREFULLY BEFORE PROCEEDING WITH THE INSTALLA-
TION. PAY PARTICULAR ATTENTION TO ALL THE PARAGRAPHS MARKED WITH THE SYMBOL
NOT READING THESE IMPORTANT INSTRUCTIONS COULD COMPROMISE THE CORRECT WORK-
ING ORDER OF THE SYSTEM AND CREATE DANGER SITUATIONS FOR THE USERS OF THE SYSTEM.
• These instructions are aimed at professionally qualified "INSTALLERS OF
ELECTRICAL EQUIPMENT" and must respect the local standards and
regulations in force. All materials used must be approved and must suit the
environment in which the installation is situated.
• All maintenance operations must be carried out by professionally qualified
technicians. Before carrying out any cleaning or maintenance operations make
sure the power is disconnected at the mains.
• This appliance must be used exclusively for the purpose for which it has been
made. "i.e. for the automation of one or two hinged gates".
The appliance may be used to operate hinged gates and doors, with gate
leaves up to 3 m in length and the following characteristics:
- maximum weight for 2-3 m long gates = 550 kg
- maximum weight for gates less than 2 m long = 700 kg
• The unit may be fitted both to the right and to the left of the passageway.
• This product and all its relative components has been designed and manu-
factured by Cardin Elettronica who have verified that the product conforms
in every aspect to the safety standards in force.
Any non authorised modifications are to be considered improper and therefore
dangerous.
The manufacturer accepts no liability for situations arising from the use of
an electrical installation which does not conform to the local standards and
regulations in force and in particular when the earthing circuit is not efficient.
IMPORTANT SAFETY INSTRUCTIONS
It is the responsibility of the installer to make sure that the following public safety
conditions are satisfied:
1) Ensure that the gate operating installation is far enough away from the main
road to eliminate possible traffic disruptions.
2) The operator must be installed on the inside of the property and not on the
public side of the gate. The gates must not swing outwards onto a public
area.
3) The gate operator is designed for use on gates through which vehicles are
passing. Pedestrians should use a separate entrance.
4) The gate must be in full view when it is operating therefore controls must
be situated in a position where the operator can see the gate at all times.
5) At least two warning signs (similar to the example on the
right) should be placed, where they can be easily seen by
the public, in the area of the system of automatic opera-
tion. One inside the property and one on the public side
of the installation. These signs must be indelible and not
hidden by any objects (such as tree branches, decorative
fencing etc.).
6) Make sure that the end-user is aware that children and/or
pets must not be allowed to play within the area of a gate installation.
If possible include this in the warning signs.
7) Whenever a fully open gate leaf comes within at least 500 mm of a fixed
structure the space must be protected by an anticrush buffer.
8) A correct earth connection is fundamental in order to guarantee the electrical
safety of the machine.
9) You are advised to protect the sistem's lateral access points with pairs of
(FTCS) photocells connected to the stop input, see installation example,
component 14 on page 2.
10) If you have any questions about the safety of the gate operating system,
do not install the operator. Contact your dealer for assistance.
TECHNICAL DESCRIPTION
800/HL251CL
Reversible geared motor, maximum opening 110°.
806/HLCF1
Embedding case in zinc plated steel with cataphoresis finish-
ing and a transmission lever for 110°.
806/HLCF1Z
Embedding case in zinc plated steel with transmission lever
for 110°.
800/HL2518CL
Reversible geared motor, gate opening 118°-360°.
806/HLCF18
Embedding case in zinc-plated steel with cataphoresis finish-
ing and accessories for gate opening 110°-360°.
806/HLCF18Z
Embedding case in zinc-plated steel with accessories for
gate opening 110°-360°.
806/HLCA140
Kit of lever accessories for a 140° opening angle.
IMPORTANT REMARKS
• Single piece geared reduction unit;
- Single phase drive motor with an incorporated overload protector and a per-
manently lubricated reversible reduction unit mounted on a cast iron stator.
- Rubber sealing gasket;
- Key operated manual release mechanism.
• Embedding case in hot rolled zinc-plated steel;
- Release unit housing in pressed aluminium.
• Transmission levers in zinc-plated steel;
- Gate fastening bracket in zinc-plated steel.
USER INSTRUCTIONS
goods or to send it back to the manufacturer if the intention is to replace
it with a new equivalent version of the same product.
Suitable differential collection, environmental friendly treatment and disposal
contributes to avoiding negative effects on the ambient and consequently
health as well as favouring the recycling of materials. Illicitly disposing of this
product by the owner is punishable by law and will be dealt with according
to the laws and standards of the individual member nation.
During the opening/closing manoeuvre check for correct operation and activate
the emergency stop button in case of danger.
During blackouts the gate can be released and manually manoeuvred using the
supplied release key (see manual release).
Periodically check the moving parts for wear and tear and grease if required,
using lubricants which maintain their friction levels unaltered throughout time
and are suitable for temperatures of -20 to +70°C (in particular the release lever
which is fitted with a greaser "J" fig. 9). In case of failure or operational anomalies
switch off the power at the mains do not attempt to repair the appliance yourself.
Periodically check the correct operation of all safety devices (photoelectric cells
etc.) Eventual repair work must be carried out by specialised personnel using
original spare parts.
INSTALLATION INSTRUCTIONS
WARNING
The minimum controls which may be installed are OPEN-STOP-CLOSE, these
AUTOMATIC OPENING
KEEP CLEAR
controls must be installed in a location not accessible to children. Before
starting with the installation of the system check that the structure which is to
be automated is in good working order and respects the local standards and
regulations in force.
CHILDREN OR PETS MUST NOT
BE ALLOWED TO PLAY ON OR
To this end make sure that the gate is sufficiently rigid (if necessary reinforce the
NEAR THE INSTALLATION
structure) and that the hinges turn easily.
You are advised to grease all the moving parts using lubricants which maintain
unaltered friction characteristics over a period of time and are suitable for tem-
peratures of -20 to +70°C.
The appliance is not suitable for continuous operation and must be contained
within the value stipulated (see technical data on page 20).
• Check the safety measures between the fixed and moving parts:
- a minimum space of 30 mm must always be left along the entire distance
between the gate and the support column measured throughout the entire
opening angle of the gate.
- make sure that the space between the bottom of the gate and the pavement
never exceeds 30 mm throughout the entire opening angle of the gate.
• The surface of the gate must not feature openings which allow a person's
hand or foot to pass through.
• Check the exact positioning of the pivots and hinges, and their good working
order (the upper and lower hinges/pivots must be aligned on the same axis).
• Work out the run of the cables according to the command and control devices
fitted and make sure the system conforms to the local standard and regula-
tions in force (see installation example fig.1 pag. 2).
• Check that the appliance is suitable for the size, weight and duty cycle of the
gate to which it is to be applied (see duty cycle on page 20).
11
11
IMPORTANT REMARKS
Attention! Only for EU customers - WEEE marking.
This symbol indicates that once the products life-span has
expired it must be disposed of separately from other rubbish.
The user is therefore obliged to either take the product to a
suitable differential collection site for electronic and electrical
Advertisement
Table of Contents
