Important Remarks; Installation Instructions - Cardin Elettronica 310/GLB242SWS Instruction Manual

IMPORTANT REMARKS

READ THE FOLLOWING REMARKS CAREFULLY BEFORE PROCEEDING WITH THE INSTALLATION.
PAY PARTICULAR ATTENTION TO ALL THE PARAGRAPHS MARKED WITH THE SYMBOL
READING THESE IMPORTANT INSTRUCTIONS COULD COMPROMISE THE CORRECT WORKING
ORDER OF THE SYSTEM AND CREATE DANGER SITUATIONS FOR THE USERS OF THE SYSTEM.
ELECTRICAL EQUIPMENT
regulations in force. All materials used must be approved and must suit
the environment in which the installation is situated.
technicians. Before carrying out any cleaning or maintenance operations
make sure the power is disconnected at the mains.
The automation of garage doors
modifications are to be considered improper and therefore dangerous.
USE
The appliance may be used to operate overhead garage doors.
For garage doors with a width of over 4 m and not more than 2,7
m in height and for garage doors with a pedestrian access door
two motors are required (one motor with on board electronics
310/GLB242SWS and one without 310/GLB240SWS).
IMPORTANT SAFETY INSTRUCTIONS
It is the responsibility of the installer to make sure that the fol-
lowing public safety conditions are satisfied:
1) The pedestrian door must not open on its own, e.g.; swing
open while the garage door is in movement
2) The appliance must not be operated when the pedestrian door
is not fully closed.
3) Make sure that there are no dangerous sharp edges.
4) Make sure that the end-user is aware that children and/or pets
must not be allowed to play within the area of a garage door
installation. If possible include this in the warning signs.
5) A correct earth connection is fundamental in order to guarantee
the electrical safety of the machine
6) If you have any questions about the safety of the door operat-
ing system, do not install the operator. Contact your dealer for
assistance.
TECHNICAL DESCRIPTION
encoder.
24 V direct current drive motor.
cast iron stator with a never ending screw.
mechanism.
310/GLB242SWS Motor with an incorporated electronic pro-
grammer complete with power stage, logic control, battery
charger and radio receiver. Power is rooted to the card by a
separate toroidal transformer housed in the same container
and connected to the card
motor without on board electronics
ACCESSORIES
316/GLO2AD - Straight telescopic arm length 700 mm.
316/GLO3A - Curved (right) telescopic arm length 700 mm.
316/GLO4A - Curved (left) telescopic arm length 700 mm.
316/GLO6A - Straight telescopic arm length 1000 mm.
316/GLOPS - Motor support extension.
316/GLOTG - Pair of pipes, pipe support brackets and DIN
threaded pins for central motor positioning.
316/GLOCGL - Ferrule and DIN threaded pin, with pipe support
brackets for lateral motor positioning.
316/GL20SB - Manual release cord.
IMPORTANT REMARKS
INSTALLERS OF
USER INSTRUCTIONS
Suitable differential collection, environmental friendly treatment and disposal
contributes to avoiding negative effects on the ambient and consequently
health as well as favouring the recycling of materials.
Illicitly disposing of this product by the owner is punishable by law and will
be dealt with according to the laws and standards of the individual member
nation.
During the opening/closing manoeuvre check for correct opera-
tion and activate the emergency stop button in case of danger.
The appliance must not be activated in the dark therefore make
sure that the night lights function correctly.
The appliance can be manually released in case of emergency
(see manual release mechanism on page 21).
Periodically check the moving parts for wear and tear and grease
if required, using lubricants which maintain their friction levels
unaltered throughout time and are suitable for temperatures of
-20 to +70°C.
In case of failure or operational anomalies switch off the power
at the mains do not attempt to repair the appliance yourself.
Periodically check the correct operation of all safety devices
(photoelectric cells, safety edge etc.).
In particular make sure that the safety edge forces the door to
invert travel direction and that weights greater than 20 kg are
not lifted.
Eventual repair work must be carried out by specialised personnel
using original spare parts.
The appliance is not suitable for continuous operation and must
be contained within the value stipulated (see technical data on
page 56).

INSTALLATION INSTRUCTIONS

The minimum controls which may be installed are SEQUENTIAL-
STOP, these controls must be installed at a height between 1,5
and 1,8 m an in a location not accessible to children. Warning
sighs or adhesive should be placed near the commands indicat-
ing the points where the risk of crushing exists.
Instruct the end user in the correct use of the manual release
device and apply permanent adhesives indicating that procedure
near the device.
Before starting with the installation of the system check that the
structure which is to be automated is in good working order and
respects the local standards and regulations in force.
Automating an existing system which has sliding or balancing
problems will not solve those problems and may even make them
worse by placing more stress on weakened or damaged areas.
To this end make sure that the runner guides slide freely and
grease all the moving parts (pins, castors etc.) using lubricants
which maintain unaltered friction characteristics over a period of
time and are suitable for temperatures of -20 to +70°C.
19
Attention! Only for EU customers - WEEE marking.
This symbol indicates that once the products life-span has expired
it must be disposed of separately from other rubbish. The user
is therefore obliged to either take the product to a suitable dif-
ferential collection site for electronic and electrical goods or to
send it back to the manufacturer if the intention is to replace it
with a new equivalent version of the same product.
IMPORTANT REMARKS
. NOT