Important Remarks; Important Safety Instructions - Cardin Elettronica 305/GLi824 Instruction Manual

IMPORTANT REMARKS

READ THE FOLLOWING REMARKS CAREFULLY BEFORE PROCEEDING WITH THE INSTALLA-
TION. PAY PARTICULAR ATTENTION TO ALL THE PARAGRAPHS MARKED WITH THE SYMBOL
NOT READING THESE IMPORTANT INSTRUCTIONS COULD COMPROMISE THE CORRECT WORK-
ING ORDER OF THE SYSTEM AND CREATE DANGER SITUATIONS FOR THE USERS OF THE SYSTEM.
THE INTEGRATED CARDIN SYSTEMS ARE DESIGNED AND BUILT
ONLY TO BE USED IN MADE TO MEASURE METALLIC STRUCTURES.
CARDIN ELETTRONICA DO NOT GUARANTEE PRODUCTS THAT
HAVE BEEN INSTALLED IN A WAY THAT DOES NOT CONFORM TO
THE SUPPLIED INDICATIONS.
It therefore follows that the structure should be constructed in such a
way as to guarantee the following characteristics:
• Suitable for housing electronic appliances;
- the upper part must be completely sealed, so as not to allow water
infiltration (IP55);
- Air vents should be fitted in both the upper and lower parts of the
columns in order to avoid condensate build up;
• Conformity with the dimensional and structural characteristics as stipu-
lated by good building practice;
• The end structure should respect the parameters as laid down by the
standards and regulations in force UNI EN 12453 with regard to main-
taining safety conditions during the use of motorized gates and doors.
• These instructions are aimed at professionally qualified "installers of electrical
equipment" and must respect the local standards and regulations in force.
All materials used must be approved and must suit the environment in which
the installation is situated.
• All maintenance operations must be carried out by professionally qualified
technicians.
Before carrying out any cleaning or maintenance operations make sure the
power is disconnected at the mains.
• This appliance must be used exclusively for the purpose for which it has been
made. "i.e. for the automation counterbalanced garage doors"
• Any unauthorised modifications are to be considered improper and therefore
dangerous.
• The motor can be positioned either to the left or to the right of the installation.

IMPORTANT SAFETY INSTRUCTIONS

• This appliance must never be used by people (including children) with physi-
cal, sensory or mental disabilities or by people without specific knowledge
and experience in its operation unless they are able to benefit from the experi-
ence or are being taught to use the appliance whilst being safeguarded by the
presence of somebody responsible for their safety.
• Before installing make sure that the guided parts are in good condition, cor-
rectly balanced and that they open and close correctly.
• Avoid becoming trapped between the moving parts and the fixed parts during
the opening and closing movements.
• The motor's power cable must be made of polychloroprene in conformity with
the international standard 60245 IEC 57.
It is the responsibility of the installer to make sure that the following public safety
conditions are satisfied:
It is the responsibility of the installer to make sure that the following public
safety conditions are satisfied:
1) The pedestrian door must not open on its own, e.g.; swing open while
the garage door is in movement.
2) The appliance must not be operated when the pedestrian door is not
fully closed.
3) Make sure that there are no dangerous sharp edges.
4) Make sure that the end-user is aware that children and/or pets must
not be allowed to play within the area of a garage door installation. If
possible include this in the warning signs.
5) A correct earth connection is fundamental in order to guarantee the
electrical safety of the machine.
6) If you have any questions about the safety of the door operating system,
do not install the operator. Contact your dealer for assistance.
8) If you have any questions about the safety of the door operating system, do
not install the operator. Contact your dealer for assistance.
IMPORTANT REMARKS
TECHNICAL DESCRIPTION
• The set consists of:
2 geared motors 300/GLi824 with an incorporated encoder without onboard
electronics.
1 electronic programmer CCi924 with NiMH batteries, a battery charger and an
integrated S449 radio frequency module.
• The geared motor is powered by 24 Vdc and is fitted with a double-reduction
kinetics system immersed in permanently fluid grease .
• The emergency manoeuvre is carried out by means of an efficient manual
release system integrated into the geared motor.
• The motor is connected to the electronic programmer by means of a 6 wire
fast-fitting cable.
• The electronic programmer is aimed at the management of 24V encoder
controlled motors for garage doors that allow door-positioning control.
Repositioning takes place automatically whenever foreign objects get in the
way of the door as it is moving.
If the motor release system has been activated a sensor positioned on the
mechanical components will force the programmer to carry out automatic
repositioning the next time a command is given.
The electronic control unit is completed by the anti-crush and "soft start" and
"soft stop" functions.
The electronic components are housed in a shock-proof plastic container
IP55 and are factory fitted with a slot-in battery charger, NiMH buffer batteries
driving the door during emergencies, an RF module for remote control and a
Liquid Crystal Display (LCD 16 digits x 2 lines) which allows all the running
functions and the number of manoeuvres carried out by the automation to be
monitored as well permitting rapid parameter and function mode setting.
USER INSTRUCTIONS
new equivalent version of the same product.
Suitable differential collection, environmental friendly treatment and disposal
contributes to avoiding negative effects on the ambient and consequently
health as well as favouring the recycling of materials. Illicitly disposing of this
product by the owner is punishable by law and will be dealt with according
to the laws and standards of the individual member nation.
During the opening/closing manoeuvre check for correct operation and activate
the emergency stop button in case of danger.
During blackouts the garage door can be released and manually manoeuvred
using the supplied release key (see manual release on pag. 14).
Periodically check the moving parts for wear and tear and grease if required using
lubricants which maintain their friction levels unaltered throughout time and are
suitable for temperatures of -20 to +70°C.
In case of failure or operational anomalies switch off the power at the mains do
not attempt to repair the appliance yourself.
Periodically check the correct operation of all safety devices (photoelectric cells
etc.). Eventual repair work must be carried out by specialised personnel using
original spare parts.
The appliance is not suitable for continuous operation and must be adjusted
according to the model (see technical data on pag. 44).
13
IMPORTANT REMARKS
Attention! Only for EU customers - WEEE marking.
This symbol indicates that once the products life-span has expired
it must be disposed of separately from other rubbish. The user is
therefore obliged to either take the product to a suitable differen-
tial collection site for electronic and electrical goods or to send
it back to the manufacturer if the intention is to replace it with a