Kubota WG1605-G-E3 Workshop Manual page 82

WG1605-G-E3,WG1605-L-E3,WG1605-GL-E3, WSM
Valve Spring
Rocker Arm Shaft to Rocker Arm
• Rocker Arm Shaft
• Rocker Arm
Push Rod
Tappet to Tappet Guide Bore
• Tappet
• Tappet Guide Bore
Timing Gear
• Crank Gear to Idle Gear 1
• Idle Gear 1 to Cam Gear
• Idle Gear 1 to Injection Pump Gear
• Idle Gear 1 to Idle Gear 2
• Idle Gear 2 to Governor Gear
Idle Gear
• Idle Gear 1
• Idle Gear 2
Camshaft
Item
Free Length
Tilt
Setting Load /
Setting Length
Oil Clearance
O.D.
I.D.
Alignment
Oil Clearance
O.D.
I.D.
Backlash
Backlash
Backlash
Backlash
Backlash
Side Clearance
Side Clearance
Side Clearance
Alignment
1-S4
Factory Specification
35.1 to 35.6 mm
1.39 to 1.40 in.
–
74 N / 31.0 mm
7.5 kgf / 31.0 mm
17 lbf / 1.22 in.
0.016 to 0.045 mm
0.00063 to 0.0017 in.
11.973 to 11.984 mm
0.47138 to 0.47181 in.
12.000 to 12.018 mm
0.47244 to 0.47314 in.
–
0.020 to 0.062 mm
0.00079 to 0.0024 in.
19.959 to 19.980 mm
0.78579 to 0.78661 in.
20.000 to 20.021 mm
0.78741 to 0.78822 in.
0.0320 to 0.115 mm
0.00126 to 0.00452 in.
0.0360 to 0.114 mm
0.00142 to 0.00448 in.
0.0340 to 0.116 mm
0.00134 to 0.00456 in.
0.0330 to 0.117 mm
0.00130 to 0.00460 in.
0.0300 to 0.117 mm
0.00119 to 0.00460 in.
0.20 to 0.51 mm
0.0079 to 0.020 in.
0.20 to 0.51 mm
0.0079 to 0.020 in.
0.0700 to 0.220 mm
0.00276 to 0.00866 in.
–
ENGINE
Allowable Limit
34.8 mm
1.37 in.
1.0 mm
0.039 in.
63 N / 31.0 mm
6.4 kgf / 31.0 mm
14 lbf / 1.22 in.
0.10 mm
0.0039 in.
–
–
0.25 mm
0.0098 in.
0.07 mm
0.003 in.
–
–
0.15 mm
0.0059 in.
0.15 mm
0.0059 in.
0.15 mm
0.0059 in.
0.15 mm
0.0059 in.
0.15 mm
0.0059 in.
0.80 mm
0.031 in.
0.80 mm
0.031 in.
0.30 mm
0.012 in.
0.01 mm
0.0004 in.
KiSC issued 01, 2012 A