Philips HDRW720 Service Manual page 45

Chrysalis (CHR)
Nucleus Name DS_CHR_DevTypeGet
Nucleus Number 100
Description Sends the device ID and the module ids and revisions of the PNX7100 (Chrysalis) to the
stdout port.
User Input None
Example DS:> 100
Device ID 7100
Codec ID PNX7100_MF2
F-BCU (0x0102) 1.0 INTC (0x011d) 1.0 PCI-XIO(0x0113) 1.0
SIF(0x013b) 1.0 EJTAG (0x0104) 0.0
BOOT (0x010a) 1.0 CONFIG (0x013f) 1.0 RESET (0x0123) 1.0
DEBUG (0x0116) 0.0
UART2 (0x0107) 0.1
I2C1 (0x0105) 0.1
DISP0 (0xa015) 0.1
SPU
CCIR (0x0139) 1.0
DV
SGDX (0xa008)0.0 BYTE (0xa00b) 0.0
ACOMP (0xa000) 0.0
SCR
AUDIO0 (0xa015) 0.1 AUDIO1 (0xa00f) 0.0 PSCAN (0xa018) 0.0
010000:
Test OK @
Nucleus Name DS_CHR_TestImageOn
Nucleus Number 101
Description Generates a test-image of a selected video standard on selected video output on the digital
board. When no input is given, the default values will be used. Use nucleus
DS_ANAB_VideoRouting to route the video signal on the analogue board output
User Input The user has to decide which test image, video standard and video output must be used:
Test image id:
0
1
2
3
4
5
6
7
8
9
10
Video standard:
PAL (default)
NTSC
Video output:
ALL
CVBS
YC
RGB
YUV
PSCAN
Example DS:> 101
010100:
Test OK @
DS:> 101 0 pal cvbs
010100:
Test OK @
DS:> 101 4 ntsc yc
010100:
Test OK @
Nucleus Name DS_CHR_TestImageOff
Nucleus Number 102
Description Switches the test-image off.
User Input None
Diagnostic Software
UART0 (0x0107) 0.1
UART3 (0x0107) 0.1
GPIO (0x013c) 1.0
DISP1 (0xa00f) 0.0
(0xa00e) 0.0 MIXER (0x0137) 1.0
VDEC (0x0133) 0.1
(0xa00c) 0.0 BEI (0xa00a) 0.0
VFE (0xa001) 0.0
(0x0000) 0.0 SIFF (0xa011) 0.0 WMD
VERTICAL_COLOURBAR (default)
HORIZONTAL_COLOURBAR
WHITE
YELLOW
CYAN
GREEN
MAGENTA
RED
BLUE
BLACK
GRAY
CVBS and YC and RGB (default)
progressive scan
HDRW720/0x, DVDR725H/0x
S-BCU (0x0102) 1.0
UART1 (0x0107) 0.1
I2C0 (0x0105) 0.1
SYNC (0x013a) 1.0
OSD (0x0136) 0.1
DENC (0x0138) 0.1
PARSER (0xa00d) 0.0
IDE (0xa009) 0.0
OUTPUT (0xa003) 0.0
VCOMP (0xa002) 0.0
(0xa010) 0.0
5. EN 45