Philips HDRW720 Service Manual page 22

Navigation in the time shift buffer
Preparation:
•) The TV set is switched on, and, if necessary, the programme number for the
DVD recorder has been selected.
•) the DVD recorder is switched to tuner mode (button TUNER ).
1 Press INFO to display the bar of the time shift buffer on the
screen.
2 The following buttons are available:
N , O , PLAY G , PAUSE 9 , D , C , JUMP
O
FWD , JUMP BACK for navigation in the time bar.
T/C
O
Switching between title/chapter for selection using N ,
O . The top screen line displays either 'TITLE' for selecting
titles or 'CHAPTER' for selecting chapters
REC/OTR n :
O
- To start a recording that will be stored on the HDD.
- To mark a title that will be stored on the HDD.
- Hold button down to separate the beginning of a title.
O Red function button:
- To cancel the marked recording that was set with the
REC/OTR n button.
- Hold button down to separate the end of a title.
O Yellow function button: ('OVERVIEW')
To display an overview of all content of the time shift buffer.
O Blue function button:('MORE INFO'):
To display any additional information for the actual TV show
transmitted by the GUIDE Plus+ ® system.
Recording on the HDD
Mark TV shows for recording
As a rule, recordings in the time shift butter are automatically deleted
after a certain time (1 to 6 hours). In order to store recordings on the
HDD permanently, you can mark sections of the time shift buffer that
will not be deleted and will be available as titles for later playback.
Mark an entire title
A title marker is set if you are watching a TV show longer than 60
seconds. (No change of programme number within 60 seconds)
If you want to mark an entire title (title marker at the beginning and at
the end), proceed as follows:
1 Press INFO to display the bar of the time shift buffer on the
screen.
O You can also press the yellow colour button to get a better
overview of the recordings.
2 Select the title you want to store with B , A .
3 Press REC/OTR n to mark the title.
P
The colour within the bar changes to red. If you press the
yellow button, you will see programmes marked for recording
with a red dot.
O To remove the marker, press the red function button. The
red title marker disappears.
4 If you want to mark other titles, repeat steps 2 3
and , until
you have selected all the titles you want.
O If you want to mark several titles in a sequence, go to the
oldest title and press REC/OTR n several times.
Using REC/OTR n you can also mark the future end of a
O
IIIIIIIIIIIIIII
title. You will see this in the red marked ' ' symbol
on the right end of the Time Shift Buffer bar.
The recording will be stoped automatically at the end of the
program.
If the start (titlemarker) of the TV-Show was not taken from
the GUIDE Plus+ ® System, or no GUIDE Plus+ ® is available,
you can extend the end by +30, +60, +90 ,... minutes
39
Recording on the HDD
Mark part of a title
You can also mark only parts of a title.
If you mark several parts of a title, each part will be stored as a
separate title on the HDD.
1 Press INFO to display the bar of the time shift buffer on the
screen.
O
You can also press the yellow colour button to get a better
overview of the recordings.
2 Select the title you want to store with B , A .
3 The following options are available:
O Freely selectable end:
- Press REC/OTR n to select the entire title. The colour
changes to red.
- Search for the desired end using D , C .
- Hold down the red button:
Red marked recording changes to its original colour from
the current position to the end of the title.
If you want to set more markers in one title, start marking at
the begin of the title.
O
Freely selectable beginning:
- Search for the desired beginning using D , C .
- Hold down the REC/OTR n button.
The marker changes to red from the current position to the
end of the title.
O Freely selectable beginning and end:
First, you must define the beginning and then cut off the end.
- Search for the desired beginning using D , C .
- Hold down the REC/OTR n button.
The marker changes to red from the current position to the
end of the title.
- Search for the desired end using D , C .
- Hold down the red button:
Red marker changes to its original colour from the current
position to the end of the title.
How can I delete the changes?
Press REC/OTR n to mark the entire title.
To remove the marker, press the red function button.
'Auto delete'
If there is no space for new recordings on the HDD, recordings will be
automatically deleted in the following order:
1) Titles that have already been viewed. Symbol 'Symb seen'.
2) Titles that were not protected. No symbol 'Symb protect'
available.
More information you will find in the chapter 'User preferences for the
HDD'.
40
Manual recordings
Recordings are always started and stored in the time shift buffer as
soon as you switch on the device.
O
You can mark a recording for storage on the HDD using
REC/OTR n on the remote control or n on the device.
Such marked recordings are displayed as a red bar in the time
shift buffer and are not automatically deleted after the time
shift buffer period (1 to 6 hours) expires.
If you switch off the DVD recorder with STANDBY m or
O
select the 'Flush Buffer' function, all other recordings of the
time shift buffer will be deleted.
If you press the red function button, the marker for the recording is
removed.
OTR recordings
Recordings made using REC/OTR n will be automatically stopped
after the end of the TV show if information is available from the
GUIDE Plus+ ® system. If no information is available, you can select the
time after which a recording will automatically stop using
REC/OTR n . (each time you press the button, you prolong the
switch-off time by 30 minutes)
If you press the red function button, the marker for the recording is
removed.
Direct Record
If the recording is manually started, the switched off DVD recorder
receives the currently selected TV channel through the scart cable. The
selected TV channel is compared with the stored TV channel of the
DVD recorder. If the TV channel can be found, the DVD recorder
selects it and starts the recording.
If no corresponding TV channel is found in the DVD recorder, an error
message appears.
Read the next section 'Switching Direct Record on or off' on how to
switch Direct Record on or off.
How does Direct Record work?
The DVD recorder compares the TV channel selected on the TV set with its
stored TV channels via the scart cable. If the same TV channel is found, the
DVD recorder switches to the corresponding programme number and starts
recording.
Please do not change channel on the TV set during search. This may affect
the tuning on the DVD recorder.
1 Select the programme number on the TV set from which you want
to make the recording.
2 Press REC/OTR n while the DVD recorder is switched off .
a 'WAIT' appears in the display
b The DVD recorder compares its stored TV channels with those of the TV
set. Please do not change channel on the TV set while 'WAIT' appears in the
display.