Table of Contents
Advertisement
register selection and write
procedure, 5-2 to 5-3
register writes, 5-1 to 5-3
SCXIbus to SCXI-1163 rear signal
connector pin equivalents, 5-2
SCXI-1163 registers, 4-1 to 4-6
Slot-Select Register, 4-8
Status Register
description, 4-5
jumper connections, 2-6
reading from Status Register, 2-24
timing diagram, 2-24
RESET* signal, 3-3, C-3
initialization, 5-3
routing circuitry, 3-4 to 3-5
S
SCXI-1163 module. See also jumper
configuration; module configuration;
theory of operation.
block diagram, 3-1
illustration, 1-1
optional equipment, 1-3 to 1-4
optional software, 1-2 to 1-3
overview, 1-1
unpacking, 1-4
SCXI-1180 feedthrough panel
cable assembly, E-12
front panel installation, E-14
installation, E-12 to E-13
rear connections, E-13
SCXI-1302 50-pin terminal block
cover removal, E-15
installation, E-15
wiring procedure, E-14
SCXI-1326 terminal block, 2-11 to 2-14
hazardous voltage warnings, 2-11
installation, 2-14
overview, 2-11
parts locator diagram, 2-13
signal connection procedure, 2-12
SCXI-1340 cable assembly, E-1 to E-2
installation, E-3
SCXI-1163 and board pinout
equivalences, E-2
SCXI-1341 Lab-NB, Lab-PC, or Lab-PC+
cable assembly, E-4
installation, E-5
pin translations, E-4
SCXI-1342 PC-LPM-16 cable assembly,
E-5
installation, E-6
© National Instruments Corporation
pin translations, E-6
SCXI-1343 rear screw terminal adapter
cable assembly, E-17
installation, E-18
pin connections, E-17 to E-18
SCXI-1344 Lab-LC cable assembly, E-4
installation, E-5
pin translations, E-4
SCXI-1348 DIO-32F cable assembly, E-10
installation, E-12
pin translations, E-11
SCXI-1350 multichassis adapter,
E-16 to E-17
SCXI-1351 and NB5 cable
cable assembly, E-7
installation, E-9 to E-10
SCXI-1163, DIO-96, AT-MIO-16D, and
AT-MIO-64F-5 pinout
equivalences, E-8 to E-9
SCXI-1351 one-slot cable extender
cable assembly, E-15
installation, E-16
SCXIbus connector
pin assignments, 3-2, C-2
SCXIbus to rear signal connector to
data acquisition board pin
equivalents, 5-2
signal descriptions, 3-3 to 3-4, C-3
SERCLK signal
digital I/O signal connections, 2-17
reading from Module ID Register, 2-23
reading from Status Register, 2-24
rear signal connector, 2-16, B-3
writing the slot-select number, 2-20
writing to registers
Address Handler, 2-21
Data Register, 2-22, 5-2 to 5-3
SERDATIN signal
digital I/O signal connections, 2-17
reading from registers
Module ID Register, 2-23
Status Register, 2-24
rear signal connector, 2-16, B-3
writing the slot-select number, 2-20
writing to registers
Address Handler, 2-21
Data Register, 2-22, 5-2 to 5-3
SERDATOUT signal
digital I/O signal connections, 2-17
jumper configuration, 2-4 to 2-7
rear signal connector, 2-16, B-3
serial configuration
rear signal connector, 2-16, B-3
Index-5
Index
SCXI-1163 User Manual
Advertisement
Table of Contents
