Base Frame - BodyCraft MA410 Instruction Manual

STEP 1
To ease the assembly process, do NOT tighten bolts until instructed.
1. Attach the Rear Stabilizer (4) to the Base Frame (1) using two 1/2" X 3-1/4" Hex Bolts (102), four 1/2"
Washers (121) and two 1/2" Nylon Nuts (129). Attach the End Cap (64) to the front of the Base
Frame (1) and attach two 50 X 75 mm End Caps (63) to the Rear Stabilizer (4).
2. Attach the Rear Upright (2) to the bolts welded on the Rear Stabilizer (4), using two 1/2" Washers
(121) and two 1/2" Nylon Nuts (129). Attach a 50 mm SQ Plug (66) to the top of the Rear Upright (2).
3. Slide the Bench Press Upright (5) over the Base Frame (1), align the holes and attach the Bench
Press Upright (5) to the Base Frame (1), using two 3/8" X 3-1/8" Hex Bolts (106), four 3/8" Washers
(122) and two 3/8" Nylon Nuts (130).
4. Lay the Top Frame (3) atop the Bench Press Upright (5), then attach to the Rear Upright (2), using
one 1/2" X 3" Hex Bolt (103) in the top threaded hole, and one 1/2" X 3-1/4" Hex Bolt (102), two 1/2"
Washers (121) and one 1/2" Nylon Nut (129) in the bottom hole. Attach the Top Frame (3) to the
Bench Press Upright (5), using two 1/2" X 1" Hex Bolts (104) and two 1/2" Washers (121).
5. Insert two Plastic Guide Rod
Holders (71) into the holes in the
weight base on the Base Frame
(1). Slide a Rubber Donut (79)
onto one end of each Guide Rod
(8) and then insert the Guide
Rods (8) into the Plastic Guide
Rod Holders (71).
6. Slide each Weight Plate (35)
over the Guide Rods (8). Make
certain that each plate is
oriented with the selector holes
on bottom and facing forward.
Attach the Top Plate (36) to the
Selector Rod (37) using the Top
Plate Bolt (97). Tighten the Top
Plate Bolts (97). Slide the Top
Plate (36) and Selector Rod (37)
onto the Guide Rods (8).
7. Insert two Plastic Guide Rod
Holders (71) into the holes in the
Top Guide Rod Retainer (13).
Slide the Top Guide Rod
Retainer (13) over the Guide
Rods (8) and then attach the
Top Guide Rod Retainer (13) to
the bolts welded on the Top
Frame (3), using two 1/2"
Washers (121) and two 1/2"
Nylon Nuts (129).
8. Attach the Lat Bar Holder (21) to
the Top Frame (3) and Rear
Upright (2), using four 3/8" X 3"
Hex Bolts (107), eight 3/8"
Washers (122) and four 3/8"
Nylon Nuts (130).
Base Frame Assembly
122
130
21
122
122
122
107
121
104
130
122
122
64
6
121
129
3
121
129
71
121
37
104
36
97
35
5
90
122
79
71
122
106
121
129
121
129
1
121
66
129
121
13
121
71
130
122
122
2
8
129
129
121
121
121
63
121
4
79
71
103
102
21
107
102
63