Advertisement
Quick Links
Advertisement
Related Manuals for BodyCraft MB1303
Summary of Contents for BodyCraft MB1303
- Page 1 HFT STRENGTH TRAINING SYSTEM OWNER'S MANUAL MB1303 Recreation Supply Inc. P.O. BOX 181 Model No. BODYCRAFT Sunbury, OH 43074 is a division of Recreation Supply...
- Page 2 8. Make certain all cables are seated within the pulleys before every use. 9. Exercise with care to avoid injury. 10. If you are unsure about the proper use of the BODYCRAFT HFT Strength Training System call your local BODYCRAFT dealer or our customer service department.
- Page 3 Gym Placement Planner If possible, please take advantage of the corner fit design. WALL 38.65" HEIGHT 55.64" 81.68" Important Notes and Tips: Recommended Tools for Assembly 1. Do not tighten any bolts until instructed. 2. Two people are reguired for the safe assembly of the gym.
- Page 4 OVERVIEW 51 51 51 51 36 69 63 69 65 36 66 54 66 54...
-
Page 5: Table Of Contents
PARTS LIST NO. DESCRIPTION QTY. BASE FRAME LEG UPRIGHT FRAME - RIGHT UPRIGHT FRAME - LEFT REAR UPRIGHT FRAME GUIDE ROD TOP FRAME - RIGHT TOP FRAME - LEFT CHIP - UP BAR TOP CROSS SUPPORT BOTTOM CROSS SUPPORT WEIGHT PANEL - RIGHT WEIGHT PANEL - LEFT SPORT BAR LONG BAR... - Page 6 PARTS LIST NO. DESCRIPTION QTY. PULLEY PLASTIC BUSHING (pre-assembled) END CAP 1" X 295L FOAM GRIP (pre-assembled) 1" X 900L FOAM GRIP (pre-assembled) SELECTOR PIN SPACER (pre-assembled) PLASTIC STUDS (8 picess pre-assembled) 1/2" BUSHING (pre-assembled) BEARING (pre-assembled) C - RING (pre-assembled) RUBBER COVER (pre-assembled) TOP PLATE BOLT 1/2"...
-
Page 7: Base Frame Leg
STEP 1 Assemble Upright Frame TWO PEOPLE ARE REQUIRED TO ASSEMBLE THIS STEP. 1. Cap two End Caps (38) to the Base Frame Leg (1). Attach Rear Upright Frame (4) to the Base Frame Leg (1) using eight 3/8" Chromed Washers (62), and eight 3/8"... - Page 8 STEP 2 Assemble Top Frame 1. Attach Right & Left Upright Frame (2R & 3L) to the two Base Frame Legs (1) using four 3/8" Chromed Washers (62), and four 3/8" Chromed Nylon Nuts (68). 2. Attach two Rotating Pulley Holders (17) to the Right & Left Pulley Height Adjuster (15R &...
-
Page 9: Top Guide Rod Holder
STEP 3 Assemble Guide Rods 1. Insert two Plastic Guide Rod Holders (24) into the holes on the Base Frame Leg (1). Insert the Guide Rods (5) into the Plastic Guide Rod Holders (24). Slide the Stack Spacers (23) onto the guide rods, followed by the two Rubber Dounts (22). NOTE: Do not install STACK SPACERS (23) if you have the optional heavy weight stack option, 38 WEIGHT PLATES (21). -
Page 10: Cable
STEP 4 Assemble Cable and Pulleys as shown Cable (27) Ball End Bolt End 1. Insert the Bolt End of the Cable (27) through Rotating Pulley Holder (17) as Figure P1, P2, route over the two pulleys mounted on the Right Top Frame (6R) as Figure P3, P4. - Page 11 STEP 5 Assemble Right & Left Panel 1. Attach Right & Left Weight Panel (10R & 11L) to the Rear Upright Frames (4) using eight Plastic Studs (43), four 1/4" X 6" Hex Bolts (54), eight 1/4" Washers (66), and four 1/4" Nylon Nuts (70). 2.
-
Page 12: Ankle Strap
STEP 6 Accessories and Exercise Guide Placement 1. Hang two Single Handles (32), Chin Assist Strap (30), Tricep Rope (31), Sport Bar (12), two Chains (33), Ankle Strap (29), and Long Bar (13) on the Top Cross Support (8). 2. Attach Exercise Book (28), Exercise Book Holder (26) and Plastic Studs (43) to the op Cross Support (8) using one M4 X 10L Sunken Head Screw (59), one M4 X 40L Sunken Head Screw (58) and two M4 Nylon Nuts (72). -
Page 13: Pulley
7. Enjoy many years of a Fit Lifestyle. Thank you for purchasing the BODYCRAFT HFT Strength Training System! If you have questions or comments, please contact your BodyCraft dealer or contact BODYCRAFT directly at 800-990-5556 or info@bodycraft.com. Please REGISTER your BODYCRAFT HFT at www.bodycraft.com...