Humidifier Control Via Network; Supervisor Variable List - Carel humiSonic User Manual

8. HUMIDIFIER CONTROL VIA NETWORK

The variables shown in the list are a set of all the internal variables. DO
NOT CONFIGURE ANY VARIABLES THAT ARE NOT SHOWN IN THE TABLE,
OTHERWISE HUMIDIFIER OPERATION MAY BE AFFECTED.
The serial connection (M11) is confi gured by default with the following
parameters:
- Address 1
- Baud rate 19200 bps
- Frame 8,N,2

8.1 Supervisor variable list

"A"
analogue variables* (Modbus®: REGISTERS)
CAREL - Modbus®
1 param. d0: Th probe temperature reading
2 param. d1: Th probe humidity reading
3 param. d2: Probe reading
4 param. d5: Set point trimmer reading
"I"
integer variables (Modbus®: REGISTERS)
CAREL Modbus®
1 129 Level access password
2 130 Firmware release
15 143 Alarms, see Cap. "ALARMS":
bit0: E0 Alarm
bit1: Et Alarm
bit2: EF Alarm
bit3: Ed Alarm
bit4: EP Alarm
20 148 Parameter A0: Operating mode
21 149 Parameter A2: Type of external sensor
22 150 Parameter A3: Probe minimum
23 151 Parameter A4: Probe maximum
24 152 Parameter A5: Probe off set
25 153 Parameter A6: Fan off delay time
26 154 Parameter A7: Fan speed
27 155 Parameter A8: Maximum evaporation time for no production alarm
28 156 Parameter A9: Minimum evaporation time for no production alarm
29 157 Parameter b0: Operating options
30 158 Parameter b1: Time between two washing cycles
31 159 Parameter b2: Inactivity time for washing on next start
32 160 Parameter b3: Washing time (fi ll + drain)
33 161 Parameter b4: Start delay time
34 162 Parameter b5: Operating hours for CL alarm
35 163 Parameter b6: Time to display new CL alarm in minutes
36 164 Parameter b7: Transducer On/Off control interval
37 165 Parameter b8: Probe delay disconnected
38 166 Reserved
39 167 Parameter bA: Maximum fi ll time
40 168 Parameter bb: Refi ll time in evaporation
41 169 Parameter bC: Maximum drain time
42 170 Parameter bd: Drain opening time to completely empty tank
43 171 Parameter bE: Delay time after measuring low level for refi lling
44 172 Parameter C0: Default display (Terminal)
45 173 Parameter C1: Parameter A0: Baud rate
46 174 Parameter C2: tLAN address (If 0 Master controller)
47 175 Parameter C3: Serial address
48 176 Parameter P0: Maximum fl ow-rate
49 177 Parameter P1: Humidity control hysteresis
50 178 Parameter P2: Low humidity alarm threshold
51 179 Parameter P3: High humidity alarm threshold
52 180 Parameter SP: Humidity set point
53 181 Parameter d3: Operating hour counter
54 182 Parameter d4: Unit hour counter (not resettable)
60 188 Serial request (If digital 37 is setted)
65 192 Parameter C4: Timeout for offl ine master serial
87 215 FW release slave 1
88 216 Instantaneous production slave 1
89 217 Slave 1 status
90 218 Phase slave 1
91 219 Alarm mask slave 1
92 220 Hour counter operation slave 1
93 221 FW release slave 2
94 222 Instantaneous production slave 2
95 223 Slave 2 status
96 224 Phase slave 2
97 225 Alarm mask slave 2
98 226 Hour counter operation slave 2
99 227 FW release slave 2
100 228 Instantaneous production slave 3
101 229 Slave 3 status
102 230 Phase slave 3
bit5: PU Alarm
bit6: H ¯ Alarm
bit7: H_ Alarm
bit8: EE Alarm
bit9: CL Alarm
23
Direct version for room applic. +0300062IE - rel. 1.0 - 10.09.2015
ENG
R/W
R
R
R
R
R/W
R/W
R
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R
R/W
R/W
R/W
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R