Table of Contents
Advertisement
Precautions for Use
Q Q Q Q Cautions when Using the Printer
WARNING
• DO NOT place metallic objects or containers with wa-
ter (flower vases, flower pots, cups, etc.) on or near
the printer. This type of situation presents a danger of
fire or electrical shock should they fall inside. ............
• DO NOT remove any of the covers from the printer as
there is a danger of electrical shock from high voltage
parts inside the printer. ...............................................
• DO NOT damage, break or attempt to repair the
power cord. DO NOT place heavy objects on the cord,
pull it, bend it unnecessarily or cause any other type of
damage.
These types of situations present a danger of fire or
electrical shock. ..........................................................
• NEVER attempt to repair or disassemble the printer or
its parts as there is a danger of fire, electrical shock or
damage to the laser. If the laser beam escapes, there
is a danger of it causing blindness. ............................
• If the printer becomes excessively hot, smoke appears
from the printer, there is an odd smell, or any other ab-
normal situation occurs, there is a danger of fire or
electrical shock. Turn the power switch OFF (O) imme-
diately, remove the power plug from the outlet and
contact your service representative. ...........................
• If anything harmful (paper clips, water, other fluids,
etc.) falls into the printer, turn the power switch OFF
(O) immediately. Next, remove the power plug from
the outlet to avoid the danger of fire or electrical
shock. Then contact your service representative. ......
• DO NOT remove or connect the power plug with wet
hands, as there is a danger of electrical shock. .........
• ALWAYS contact your service representative for main-
tenance or repair of internal parts. .............................
CAUTION
• DO NOT pull the power cord when removing it from
the outlet. If the power cord is pulled, the wires may
become broken and there is a danger of fire or electri-
cal shock. (ALWAYS grasp the power plug when re-
moving the power cord from the outlet.) .....................
• ALWAYS remove the power plug from the outlet when
moving the printer. If the power cord is damaged,
there is a danger of fire or electrical shock. ................
• If the printer will not be used for a short period of time
(overnight, etc.), turn the power switch OFF (O).
If it will not be used for an extended period of time (va-
cations, etc.), remove the power plug from the outlet
for safety purposes during the time the printer is not in
use. .............................................................................
• When lifting or moving the printer, draw the 4 handles
of the both sides of the printer, then ALWAYS hold the
designated 4 handles by more than 4 persons only. ..
• For safety purposes. ALWAYS remove the power
plug from the outlet when performing cleaning oper-
ations. ...................................................................
• If dust accumulates within the printer, there is a dan-
ger of fire or other trouble. It is therefore recom-
mended
that
you
consult
representative in regard to cleaning of internal parts.
This is particularly effective if accomplished prior to
seasons of high humidity. Consult with your service
representative in regard to the cost of cleaning the in-
ternal parts of the printer. ............................................
Other Precautions
• DO NOT place heavy objects on the printer or cause
other damage to the printer.
• DO NOT open the front cover, turn off the main switch,
or pull out the power plug during printing.
• During printing, some ozone is released, but the
amount does not cause any ill effect to one's health. If,
however, the printer is used over a long period of time
in a poorly ventilated room or when printing an ex-
tremely large number of copies, the smell may be-
come unpleasant. To maintain the appropriate
environment for print work, it is suggested that the
room be properly ventilated.
• DO NOT touch electrical parts, such as connectors or
printed circuit boards. They could be damaged by
static electricity.
• DO NOT attempt to perform any operations not ex-
plained in this handbook.
• CAUTION: Use of controls or adjustments or perfor-
mance of procedures other than those specified
herein may result in hazardous radiation exposure.
with
your
service
9
Advertisement
Chapters
Table of Contents
